1) Definition of urban amenity

Urban amenity means that residents in urban space can live and act safely and comfortably in general. This term was first used in the UK in terms of urban planning in the mid-19th century to early 20th century to indicate a core meaning “a residential area or city that is livable and comfortable and pleasant to live”. The term “amenity” in residential areas is interpreted that it is ensured when not only arrangement of living environmental facilities (roads, water supply and sewage systems, parks etc.) but also other factors that provide daily living with comfort (high dimensional and cultural requirements such as elimination of noise, daily sunlight, greenery, privacy, or scenery, or cleanliness) [11] .

2) Evaluation index of urban amenity

Reference [12] proposed a planning indice of amenity plan index for urban amenity in a broad sense, which is listed in “Table 1”. In the table, the evaluation index is largely divided into four divisions: prevention of environment pollution, natural friendly, beautiful and productive city, and history preservation and culture creation. Each of them has its own critical indices. The critical indices in the division of prevention of environmental pollution are cleanliness of air, cleanliness of water quality, quietness, and clean and purification. For natural friendly, naturalness of abundant forest, abundant green field, familiarity with water front, and familiarity with soil were set as critical detailed indices.

As such, “cleanness of air” is included in the indices that improve urban amenity. To maintain and improve clean air, cold air or fresh wind created in urban green fields and flown into cities is needed.

3) Cold air for improvement of urban amenity

One of the most known environmental problems in cities is an urban heat island. Due to urban heat island, comfort of life for residents in cities is degraded significantly. One of the solutions to the urban heat island can be cold wind mentioned in the above.

Cold wind is characterized that it is created from mountain areas around cities and flows into urban areas due to differences in height of terrains (refer to “Figure 1”). This is a natural convection phenomenon occurred due to differences in specific heat between natural and artificial land covers. That is, hot air during the daytime in cities meet with highly dense cold air descended from the surrounding area after sunset, which moves hot air into the upper layer thereby incurring a natural circulation. Through this process, urban air can maintain cleanness and furthermore, urban amenity can be improved.

1) Overview of KLAM_21

KLAM_21 (Kaltluftabflussmodell_21) is a model for cold wind creation and flow simulation test developed by the German Meteorological Agency, which is designed to analyzed and predict creation and flow of cold wind based on terrains and land usage. In addition, KLAM_21 was developed to provide basic data for pre-assessment or consultation of microclimate changes due to urban development or regional development [13] .

The characteristics of KLAM_21 require terrain data, land usage, and land cover data basically and such data are stored in a grid unit as a specific region is divided into a certain size of grid. Based on this, simulation tests about creation and flow of cold wind, height of cold wind, wind direction, wind velocity, and expansion of pollution source can be conducted. Up to 1500 × 1500 grids can be created and a single grid can process up to 25 m theoretically. Based on the

above information, a city size where simulations can be done is 37.5 × 37.5 km², which can be highly useful model to see changes in microclimate due to urban development or regional development in a broad area. In addition to simulations of flow and creation of cold wind and expansion of pollution source, KLAM_21 can analyze a level of changes in wind flow due to barriers of block type. It has also nesting function, which is convenient to enlarge a cold wind flow in specific regions [14] .

2) Operation method and process of KLAM_21

In order to perform simulation tests of cold wind creation and flow using KLAM_21, making a study area into a certain distance of grids shall be done first. Based on the grids, basic data must be inputted to enable efficient simulation tests as mentioned earlier. Next, topography data per grid as well as land cover data per grid are inputted simultaneously for data input. In the land cover classification, KLAM_21 divides land cover into nine classification standards basically. Each of land cover has its own attribute values such as the building coverage, length of roughness, wall index, height of trees, and relative radiant quantity. Whether cold wind is created or flows is determined based on the above attribute values.

Once the above grid process and data input process are complete, a script is created finally to perform simulation tests well. Here, types of simulation test results, storage interval of analysis and result are set up. Through the above processes, simulation test results of cold wind creation and flow can be derived. Based on this, cold air height and flow range in the study area as well as analysis results on cold air flow rate and direction can be obtained (refer to “Figure 2”).

In this study, study results were derived through the process shown in “Figure 3” for efficient and accurate evaluation. First, a study area was selected for evaluation and then AWS devices are installed in the study area to collect measured data thereby deriving measured values in the study area. Along with this, the study area is modeled with specific conditions to derive model data and KLAM_21 is operated to derive a model value. Finally, derived and measured values and model values are compared and analyzed thereby performing evaluations on the model.

In order to evaluate the analysis model of cold wind creation and flow accurately, the study area was divided into one district in the mountain around the city where cold wind was created, two districts near the stream where cold wind flew to the city, and two districts in the existing downtown expected to have the cold wind effect. The detailed contents of the selected study area are as follows:

1) Location and overview of the measured locations in the study area

The study area was Daegu Metropolitan City according to the administrative district system and measured points were five locations: mountain area around the city (A point), around the stream in the city (B and C points), and existing downtown (D and E points). The study area was surrounded by Mt. Palgong to the north and Mt. Biseul to the south and gradual hills and fields in the east and west directions, which were relatively open space and places that were suitable to create cold and fresh wind due to the topographical conditions (refer to “Figure 4”).

2) General status of the study area

a) Meteorological status of the study area

The study area is included in Daegu Metropolitan City according to the administrative district system as mentioned in the above. The meteorological status in Daegu Metropolitan City in the measured period (Aug. 10-Sep. 10 of 2016) showed that its average temperature was 27.9˚C and the maximum and minimum temperatures were 36.3˚C and 20.1˚C. The average cloudiness was 7.0 and total precipitation was 327.1 mm. The average wind velocity was 2.1 m/s and the maximum wind direction was normally east-southeasterly wind [15] .

b) Land cover status by location in the study area

In order to investigate the land cover status by location in the study area, a range was set within a radius of 200 m in each point and the results were found by points according to the land cover classification standards in the Ministry of Environment, which are shown in “Table 2”.

A point, which was a mountain area near the city has the following land cover status. A low density residential area was the largest as 67.7% followed by field and paddies. B point, which was near the stream in the city, other bare lands accounted for 48.8%. C point showed that traffic area accounted for 42.0%, which was the largest, followed by inland water, which accounted for 18.9%. Finally, D and E points, which were existing downtowns, had densely populated residential areas, which accounted for 84.7% and 76.6% and showed typical land cover status of residential area.

1) Collection of measured data

In order to collect measured data of study area, Automatic Weather Station (AWS) devices were installed at all areas except for E area and meteorological data for one month from August 10 to September 10 in 2016 were collected. The detailed installation conditions are listed in “Table 3”, which are applied to all areas in the same manner. For E area, collected data at the AWS devices installed by the Korea Meteorological Administration (KMA) were extracted only for the same period and utilized in the analysis.

2) Analysis of measured data

Based on the above results in the measured period, all data of average wind direction and velocity by hour on the basis of 24 hour for one month were analyzed to compare the measured results with the model data. Among the results, data of wind direction and velocity after 21:00 to 06:00 in the next day, in which cold wind was created and flown in terms of urban amenity, were found as shown in “Table 4”.

1) Simulation conditions for model data analysis

a) Modelling conditions for simulation

In order to analyze model data and collect result data, this study set the mountain point in the study area up to 25 km-long and 25 km-wide range and a height of model data were set to 5 m, which was the same installation height with the measuring equipment. The initial condition was set to store required data by dividing the area into 1250 in the horizontal direction and 1250 in the vertical direction by having a gap between grids to 20 m for modeling. In addition, the input for regional wind that can consider accurate wind direction and velocity of fresh wind was set to wind direction of 112.5˚ (east-southeasterly wind) and wind velocity of 2.1 m/s based on the meteorological status in Daegu Metropolitan City. The simulation tests were conducted based on the above data (refer to “Table 5”).

WV: Wind Velocity, WD: Wind Direction.

b) Land cover classification and related parameters for simulation

The land cover classification for simulation was based on the land cover classification in the Ministry of Environment and then reclassified according to the land cover classification standards required by the model as listed in “Table 6”. The basic values in the model were used as the parameters corresponding to each of land cover without change. Note that for high density residence, mid-density residence, low density resident, downtown, and industrial district, parameter values that corresponded to a building-to-land ratio and building height were modified and used on the basis of the current status data of buildings in Daegu Metropolitan City.

The result of land cover classification of the study area according to the above modeling conditions and land cover classification is shown in “Figure 5”.

2) Analysis of model data

a) Result of the simulation

The results of the simulation tests by main hours derived through the above modeling are shown in “Table 7”. The table indicated overall that Mt. Palgong in the north and Mt. Biseul in the south formed fresh wind earnestly from 21H after the sunset at the surrounding mountain areas and the flow of the fresh wind had been stabilized after 24H gradually. The result of wind velocity showed that the base of the valley had faster wind velocity than other surrounding areas.

b) Analysis of model data

“Table 8” shows the analysis result of model data by main hours, which were derived via the simulation test on the study area. For A point, which is a mountain area around the city, an average wind velocity was 0.48 m/s and a wind direction was southerly wind. For B point around the stream in the city, an average wind velocity was 1.24 m/s and a wind direction was southerly. For C point, its average wind velocity was 0.91 m/s and a wind direction was south-southwest wind. Finally, for D point, which is an existing downtown area, its average wind velocity was 0.13 m/s and its wind direction was easterly. For E point, its average wind velocity was 0.16 m/s and its wind direction was east-south-east wind.

LR: Length of Roughness, BC: Building Coverage, HB: Height of Building, WI: Wall Index, PMR: Plant Materials Rate, HT: Height of Trees, VI: Vertical Index, RRQ: Relative Radiant Quantity.

WV: Wind Velocity, WD: Wind Direction.

Measured data collected from the study area and model data derived through simulation tests were compared thereby deriving the result of evaluation on the cold wind creation and flow model, which is the ultimate object of this study.

The overall results of wind velocity and direction showed that wind directions had highly similar results between measured and modeled data whereas wind velocities showed somewhat different results except for A point, which was a mountain area near the city.

The regional data results divided by mountain area around the city, stream area in the city, and existing downtown showed that a mountain area had similar results of wind direction and velocity between them and a stream area in the city had a slight difference in wind velocity but similar wind direction between two data. Finally, points of existing downtown showed that a wind velocity was much different from each other but wind direction indicated similar results except for some hour slots such as 24:00 and 1:00. These results are considered as good results considering the interference among various elements in the downtown (refer to “Table 9”).

The above results were compared quantitatively, which are shown in Table 10. More specifically, the results are described as below:

For A point, which is a mountain area around the city, measured value (0.45 m/s) and model value (0.48 m/s) were nearly the same while wind directions of them showed similar results between measured value (south-southeasterly wind (157.5˚)) and model value (southerly wind (181.2˚)). For B point, which a stream area in the city, measured value of wind velocity was 1.62 m/s and that of model value was 1.24 m/s, resulting in a difference of 0.38 m/s whereas wind directions revealed similar results between measured value (south-southeasterly wind (202.5˚)) and model value (southerly wind (182.9˚)). For C point, a measured value of wind velocity was 0.48 m/s and model value was 0.91 m/s, indicating that a model value was 0.43 m/s higher than measured value whereas wind direction revealed nearly the same results between measured value (202.5˚) and model value (197.7˚).

For D point, which is existing downtown, a difference in wind velocity between measured (0.88 m/s) and model (0.13 m/s) values was 0.75 m/s while wind direction showed a difference after sunset until the midnight but after 1:00 am the next day both of measured value (east northeasterly wind (67.5˚)) and model value (easterly wind (90.0˚)) had similar wind directions despite some difference to some extent. For E point, measured value (2.46 m/s) and model value (0.16 m/s) had a large difference as 2.3 m/s whereas wind directions of both data were east-southeasterly wind, revealing the same results between measured value (112.5˚) and model value (114.3˚).

MT: Mountain, ST: Stream, DT: Downtown, WV: Wind Velocity(m/s), WD: Wind Direction(Degree), M: Measured Data, S: Simulated Data.

The summary of the verification results on the cold wind creation and flow model through comparisons and evaluations on measured and modeled values indicated that the model used in this study was found as appropriate model to analyze cold wind created at the surrounding areas of the city and overall flows of the wind into the downtown. However, a slight difference was shown in wind velocities in detail, which indicated the limitation of the cold wind creation and flow model used in this study. If more specific modeling and unit load per parameter about the study area are identified, the error range will be reduced. Thus, the model will be utilized fully in the future if the above recommendations are taken into consideration.