As shown in Table 1, the materials and chemicals used for the experiments are Filtrate reducer (Homemade XR-X), 2-Acrylamide-2-methylpro panesulfonic acid (AMPS), acrylic acid (AA), N-isopropylacrylamide (NIPAM), nano-calcium bentonite, calcium bentonite, evaluation soil (industrial grade), Ammonium persulfate, sodium bisulfite, sodium carbonate, sodium bicarbonate, calcium chloride, magnesium chloride, sodium chloride (analytical reagent).

The apparatus used to conduct the experiment comprise spulverizer, dryer, heating roller furnace, high speed homogenizer, thermostat water bath cauldron, Six-speed rotatory viscometer, SD-multiple medium pressure filter tester, HTHP high pressure high temperature filter tester, infrared spectrometer, NETZSCH TG 209 F1 type thermogravimetric analyzer, etc.

100 g of AMPS was dissolved in distilled water and 40 g of AA was added into the mixture, a certain concentration of sodium hydroxide solution is added to adjust the PH to 7. NIPAM was added proportionally until fully dissolved at 35˚C, then Nanometer calcium bentonite and initiating agent was added and stirred evenly, After 50 minutes’ reaction, N₂ gas was injected for protection. It was shattered after 8 hour’s vacuum drying at 110˚C. Finally XR-X series powder filtrate reducer sample was obtained.

Prepare compound brine base:

1000 ml distilled water + 45.70 g NaCl + 7.40 g CaCl₂ + 19.70 g MgCl₂ as the combination, 350 ml compound brine is taken, 9.00 g Na₂CO₃ and 149.00 g calcium bentonite are added under the extraordinary speed stirring condition, then we could get the compound brine. Take 350 ml brine of the corresponding NaCl concentration we have compounded. 1.00 g NaHCO₃ and 35.00 g evaluation soil are added under the high speed stirring condition that is brine base. The polymer we have already compounded is added, carry on the filtration determination under the room temperature condition and high temperature aging condition. Verify whether the synthetic polymer meets the actual field or not. Use of six-speed rotatory viscometer to evaluate the viscosity changes before and after adding the polymer drilling fluid, analyze how the synthetic sample influence the rheological property of drilling fluid. And keep on IR characterization to the synthetic polymer.

0.7% XR-X series sample in the compound brine and brine base which we have just compounded should be added, seal under 25˚C ± 3˚C the condition maintains 24 h, measure room temperature API filter loss. 1.5% XR-X series sample in the compound brine and brine base which we have just compounded are added, seal under 25˚C ± 3˚C the condition maintains 6 h, after high speed stirring, aging at 220˚C, After cooling to room temperature, carrying on HTHP filter loss (3.5 MPa, 150˚C) and rheological property measurement. The results are shown in Table 2-4 respectively.

From Tables 2-4, we can see XR-X series filtrate reducer has good capacity of filter loss in compound brine and 20% NaCl brine base, also the ability of anti temperature, which can reach 220˚C.

The XR-2 of XR-X series sample will be chosen, we will carry on infrared spectrum analysis after purify and dry it by using acetone, as shown in Figure 1. Secondary amide characteristic absorption center is at 3423 cm⁻¹, stretching vibration absorption center of -CH₂- is at 2933 cm⁻¹, sulfonic group characteristic absorption centered respectively at 1186 cm⁻¹, 1116 cm⁻¹, 1042 cm⁻¹, stretching vibration absorption center of C-S is at 628 cm⁻¹, the characteristic absorption center of C=O is at 4.1654 cm⁻¹ [6] [7] [8] .

From Figure 1, we can see the sample contain Carboxyl, secondary amides, sulfonic group and other functional molecule groups, Carboxyl and sulfonic group have strong capacity of hydratability. Amide has good ability of clay adsorption. Sulfonic group anti temperature and calcium resistant well. The C-C structure of the polymer itself has excellent thermal stability. Therefore the synthesis polymer owns the good performance of anti temperature, salt resistant and filtrate loss.

In the process of heating to high temperature, the polymer molecule may occur physical and chemical changes such as dehydration, decomposition, and oxidation. The structure of the molecule will be destroyed obviously, resulting in change the performance of drilling fluid filtrate reducer, thus affecting the rheology of the whole drilling fluid system. In the process, the mass of the polymer may change. Therefore, Thermogravimetric analysis (TG) can be utilized to investigate the thermal stability of the filtrate reducer [9] [10] [11] .

Using NETZSCH TG 209 F1 type thermogravimetric analyzer to test the thermal stability of polymer filtrate reducer in nitrogen gas, heating rate 10 K/min, gas flow rate 50 mL/min, heating rate of K/min, the results of TG analysis are shown in Figure 2 [11] [12] [13] .

From Figure 2, we can see the mass of XR-2 polymer filtrate reducer loss slowly with the increase of temperature, After the temperature surpasses 250˚C, the mass start to lose rapidly, However, mass loss of polymer filtrate reducer in the range of 0˚C - 200˚C is relatively slow. However, the mass loss of polymer filtrate reducer in the range of 0˚C - 200˚C is relatively slow. The mass loss rate is only 5.25% when the temperature reaches 220˚C or so. It is indicated that the synthetic polymer filtrate reducer can withstand 220˚C high temperature [14] [15] [16] .

Biyang 432 well is situated in the south of Chengdian Village, Gaodian, Biyang County, Henan Province. The Biyang 431 well is situated in Henan Province with convenient transportation. Its structure is situated in the lower two southwestern wings of the lower Biyang depression. The main purpose of the two wells is to carry out and preliminaries explore the hydrocarbon-bearing properties of the tight sandstone and fault-lithologic trap in the three lower part of the fault nucleus of the 189 well district, and to search for new geological reserves. The strata of this district are composed of Quaternary Plain Group, Neogene Fenghuangzhen Formation and Paleogene Walnut Group from top to bottom.

1) Plains Group and Fenghuangzhen Formation: Reddish-pale yellow mudstone, light gray-greyish red gravel sandstone is present in the form of unequal thickness interbedded layers with loose strata.

2) Liao Zhuang group: variegated, greyish gravel sandstone and gray, reddish brown sandstone are present in the form of unequal thickness interbedded layers.

3) A nuclear section: gray, gray-brown mudstone and gray-white, light gray gravel sandstone, fine sandstone is found in the form of unequal thickness interbedded layers.

4) The second section of the atomic: gray, dark gray, gray-brown mudstone, shale and off-white, light gray gravel sandstone, fine sandstone are present in the form of unequal thickness interbed.

5) The third section of the core is mainly light gray, brownish gray, taupe gravel sandstone, gravel sandstone, fine sandstone, argillaceous siltstone, gray mudstone, dark gray mudstone, beige mudstone, shale are present in the form of unequal thickness interbedded layers.

1) Before drilling, mix bentonite slurry 80 m³, add circulating water and 0.3% soda ash in a circulating tank, and then, 5% to 8% bentonite will be added to the mixing hopper in the mixing condition, mix the prehydration above 24 h and set aside for reserve.

2) Develop a coating liquid with a concentration of 0.5% - 1.0% and a volume of 20 m³. During the drilling process, prepared glue is uniformly added to the drilling fluid according to the cycle, and the drilling fluid performance is adjusted: the density is less than 1.05 g/cm³, and the viscosity is between 50 s and 80 s.

3) Depending on the lithology of the formation and the size of the drill cuttings, the size of the screen should be selected cautiously. The mesh number should be chosen to meet the minimum loss of drilling fluid to maximize the removal of solid particles in the slurry.

4) Take full advantage of solid-control equipment to strictly control the drilling fluid in useless solid content.

5) Reserve an appropriate amount of plugging material is utilized to deal with the loss.

6) Preparation of high viscosity drilling fluid in the liquid storage tank for the wellbore cleaning.

7) After drilling, turn the large displacement power to wash the well and fully circulate the drilling fluid to reduce the sand content to less than 0.5%. When there is no sand in vibrating screen basically, make a short drilling operation.

8) After short trip, fully circulate 2 cycles to 3 cycles, clean the wellbore with high-viscosity drilling fluid to ensure smooth casing.

9) In the process of drilling, PAC141 and H4-HPAN polymer colloid are supplemented to keep the polymer concentration and enhance the inhibition of drilling fluid in time.

10) Maintain the drilling fluid treatment agent normally, and make the XR-X filtrate loss agent match into the glue liquid according to the design formula as far as possible, add it into the drilling fluid according to the cycle period, and try not to directly add the dry powder treatment agent into the circulating drilling fluid.

11) Adding 2% content of ZRH-2 into the inclined section to increase the lubrication performance of the system.

12) Drilling to 2600 - 2800 m or so, adding XR-X fluid loss agent drilling fluid system to improve the drilling fluid system temperature resistance, reduce the high temperature filtration.

13) Before entering the target reservoir, the performance of drilling fluid should be strictly controlled in the designed range, especially the density and the loss of the filtrate cannot exceed the design requirements. The API filtration loss should be controlled within 5 ml and the HTHP filtration loss within 15 ml, to protect the reservoir.

14) Make full use of solid-control equipment, control the poor solid phase and low-density solid phase in the drilling fluid strictly, always make the drilling fluid sand content less than 0.5%.

15) Deal with drilling fluid in advance before the drill is finished, and maintain uniform and stable performance of the drilling fluid, generally speaking, operators do not have to make large-scale treatment. The drilling fluid is circulated more than 2 cycles before drilling to fully clean the well, so as to ensure the smooth electrical measurement.

The ammonium salt water loss agent (0.8% glue liquid) was used before 2635 m of 432 oil well, The amount of XR-X fluid loss additive (0.5% glue solution) after 2635 m was added after 2635 m of No.432 oil well, and the solution concentration of 3183 m-4643 XR-X drops is 0.8%, no foaming and tackifying, Oil well use of low viscose liquid (1% XR-X water loss agent glue) after 4643 m. As can be seen from Table 5, after using XR-X fluid loss agent drilling fluid, drilling fluid API filtration lost from 12.0 ml to 5.0 ml, HTHP filtration loss from 16.0 ml to 10.0 ml, The filtrate loss of drilling fluid is controlled steadily and effectively, the other indicators of liquid meet the requirements, better meet the drilling requirements.

Adding 1% XR-X drops to the 2851 m of the 431 oil well, As shown in Table 6, the API filtration loss of drilling fluid in wells was reduced from 7.6 ml to 5.0 ml, the filtration loss of HTHP from 15.2 ml to 10 ml, The fluid loss performance is obvious, which can effectively control the fluid loss of the drilling fluid and control the fluid loss within a reasonable range to ensure underground safety.