Fan-type piezoelectric energy harvesting technology utilizes the working principle of the fan, drives the turbine mechanism to rotate through the wind energy, and then causes bending deformation of piezoelectric components through the transmission mechanism.

In 2003 two Japanese companies NEC TOKIN and Heardea developed a piezoelectric vision navigation mark [6] . The mark was a circular with diameter of about 12.3 cm. The outer configuration was a plume shaped object and the internal configuration was a piezoelectric conversion device, a steel ball and six LED lamps. The construction of the mark was shown in Figure 1. In the highway tunnel with large traffic volume, the mark could be rotated by the wind generated from the passing cars. Because the steel ball was located in the circular channel divided by the piezoelectric conversion element, the ball would be picked up and then fall in the channel when the mark rotated. The movement of the ball would go round and begin again with the rotation of the mark. The LED lamps were lighted by the collision of the falling ball and the piezoelectric element. The device could be used in power generation. When wind speed was 3 - 6 m/s, the device lighted 3 times per second, lasted more than 3 ms and the brightness of 4000 mcd or more, could be seen in the 200 m distance.

American Texas State University developed a miniature wind driven piezoelectric power generation device [7] , as shown in Figure 2. The device used a wind wheel which made 12 piezoelectric cantilever beams vibrate, and electric energy was generated in the piezoelectric layer on the twin beams. The size of the single piezoelectric cantilever beam was 60 mm × 20 mm × 0.6 mm, and the size of the entire power generation device was 5.08 cm × 11.6 cm × 7.7 cm. The device could generate 12 mW electric power.

In 2015 Hyun Jun Jung [8] designed a piezoelectric impact-based micro wind energy harvester. The harvester was shown in Figure 3. The experimental results showed that the optimized PIMWEH generated 2.8 mw.

In 2018 Luo [9] proposed the piezoelectric generator with wind cups. The generator was shown in Figure 4. The results showed that the starting wind speed of the experiment was about 3 m/s, and the optimal load of rectangular and trapezoidal piezoelectric cantilevers was 25 KΩ with corresponding output power of 0.11 mW and 0.13 mW.

The main characteristics of fan type piezoelectric energy harvesting technology include:

1) Fan-type piezoelectric energy harvesting technology can increase the contact area with natural wind through turbine mechanism, so that wind energy can be effectively utilized.

2) Complex turbine mechanism and transmission mechanism are installed in the fan-type piezoelectric energy capture device, which enlarges the volume of the device and is not conducive to miniaturization.

3) The efficiency of the complex transmission mechanism in the fan-type piezoelectric energy harvesting device is seriously reduced due to friction and other reasons.

Wind-induced vibration piezoelectric energy harvesting technology refers to mechanical vibration caused by natural wind directly acting on the device, thus causing bending deformation of piezoelectric components.

In 2006 American Minnesota state university developed a piezoelectric wind generator adopting double piezoelectric film PVDF [10] . The size of the generator was 245 mm × 178 mm × 308 mm. The output power was 10 mW and the power density was up to 4.4 W/cm³ at the wind speed 19.3 km/h and the resistive load 200 kΩ.

In 2010 the South Korean scholars designed a portable wind generator [11] , as shown in Figure 5. Fan device caused the variation of air to drive the vibration of piezoelectric cantilever beam, thus output power. The size of the generator was 250 mm × 250 mm × 250 mm. The output voltage was 4.05 V at the wind speed 3.5 m/s and the resonant frequency 42.7 Hz.

In 2010 the South Korean scholars developed a small wind generator, as shown in Figure 6 [12] . The appearance of the generator looked like the word “T”. The output voltage was 130 V and the power was 4 mW at the wind speed 15m/s , the resonant frequency 6.17 Hz and the resistive load 4 MΩ.

In 2010 American scholars studied a kind of portable vortex induced vibration generator [13] , as shown in Figure 7. Cylindrical body produced vortex induced vibration under the action of wind, accordingly the piezoelectric ball vibrated and induced deformation, thus generated electric energy. The size of the generator was 20 mm × 20 mm × 255 mm. The power was 20 µW at the wind speed 1 - 3 m/s.

In 2012 Singapore scholars developed a micro wind energy harvester by MEMS process [14] , as shown in Figure 8. The bending of the cantilever beam structure was used to increase the force of the wind load, and then improve the electric generation efficiency. The output voltage was 18.1 mV and the power was 3.3 nW at the wind speed 15.6 m/s and the resistive load 100 kΩ.

In 2013 the University of Michigan scholars developed a turbine type wind energy harvester based on the principle of piezoelectric, as shown in Figure 9 [15] . On the piezoelectric cantilever tip and the rotating parts the permanent magnet were arranged, when the air flow drived the blade to rotate, the permanent magnet induced alternately attraction and repulsion by mutual force, which drived the vibration of the piezoelectric cantilever beam, thus wind energy was converted into electric energy. The size of the generator was 80 mm × 80 mm × 175 mm. The generator could generate milliwatts of power from wind as slow as 2˚ m/s.

In 2012 a resonant cavity type piezoelectric micro wind energy harvester based on the principle of piezoelectric was developed by the Chinese scholars, as shown in Figure 10 [16] . The force of wind load on the piezoelectric cantilever beam was amplified by using the resonant cavity structure, and the flexible beam Structure was used to reduce the critical wind speed of wind collector. The size of the generator was 64 mm × 22 mm × 14 mm. The generator could generate 1.28 mW of power from the wind speed 17 m/s.

In 2018 Sibel Akkaya [17] Oy designed and tested a new piezoelectric-based low-power wind generator to generate cheap and clean energy. The generator was shown in Figure 11. The generator included an unbalanced propeller and a piezoelectric material equipped board. The average power output of 519 μw was achieved at the 4.5 - 5 m/s wind speed range.

In 2011, Sirohi [18] designed a mirco galloping motion piezoelectric generator which was shown in Figure 12. The generator included two piezoelectric cantilevers and one equilateral triangular prism. The test results showed that when the wind speed was 11.6 mph, the maximum output power was up to 53 mW.

The main characteristics of wind-induced vibration piezoelectric energy harvesting technology include:

1) The wind-induced vibration piezoelectric energy harvesting device has no intermediate transmission mechanism, which improves the efficiency of power generation.

2) Wind-induced vibration piezoelectric energy harvesting device is easy to realize miniaturization.

3) In wind-induced vibration piezoelectric energy harvesting device, the contact area between piezoelectric elements and natural wind force is small, and wind energy cannot be fully utilized.