Frequency Selective Surfaces (FSSs), which find widespread applications as filters for microwaves and optical signals, have been the subject of extensive studies in recent years [1-4]. These surfaces include a periodically arranged metallic patch elements or aperture elements within a metallic screen and exhibit total reflection (patches) or Transmission (apertures) in the neighborhood of the element resonance [1]. Their performances depend on the substrate characteristics, element type, dimensions and the spacing between elements.

The response parameters are predicted by analyzing the surface using different techniques [5-7]. However, the small dimensions of the circuit produce some problems in result precisions. Thus, the coupling conditions between the different elements must be taken into account. Then, the efficiency of used method, their memory consumption and time requirement are usually made these methods unsuitable for optimization.

This paper presents the analysis of simple and complex passive FSS by the iterative method (WCIP). The WCIP technique takes the advantage of simplicity in its procedure based on Fast Modal Transform (FMT) in passage between spatial and spectral domain [8,9]. In addition, there is no matrix inversion was required and the convergence was insured independently of the circuit complexity. Further, there is unlimited shapes of circuit are imposed [10]. The simulation results are validated with those calculated with HFSS commercial code and recently published experimental results.

The general Frequency Selective Surface structure is depicted in Figure 1. The circuit interface is constituted of two sub domains: metal and dielectric. It is deposed on homogeneous dielectric substrate with thickness h and permittivity.

WCIP method is based on the full wave transverse wave formulation and the on collection of information at the interfaces. A multiple reflection procedure is started using initial conditions and stopped once convergence which is achieved. Two related operators incidented waves and scattered waves in the spatial domain and in the spectral domain governs the iterative procedure. They are: the scatting operator and the reflection.

We consider the printed circuit, the wave concept is

introduced to express the boundary conditions on the interface Ω (Figure 2).

The incident waves and the scattered waves are calculated from the tangential electric and magnetic fields and as:

where i indicates the medium 1 or 2 corresponding to a given interface. is the characteristic impedance of the same medium i and being the surface current density vector given as:

with n being the outward vector normal to the interface. Thus, the tangential electric and magnetic fields can be calculated from:

The scattered waves are related to the incident waves as:

is a scattering operator defines in the spatial and it accounts for the boundary conditions. The scattered waves will be reflect to generate the incident waves for the next iteration but after adding the incident source waves:

being the reflection operator and it is defined in the spectral domain.

In order to validate our method, we consider at first the structure of Figure 3. The dashed lines are the hypothetical periodic walls assumed to reduce the analysis to that of the repeated unit cell with dimensions of a = 3 mm, b = 3 mm, h₁ = 4 mm, h₂ = 3.125 mm, ε_r2 = 2.6, ε_r1 = 1. The TE01 mode is used as excitation and the iterative process is stopped after 200 iteration. The results of our method are compared to those calculated with HFSS and depicted in Figures 4 and 5 for the reflected and the transmitted respectively coefficient. In the two cases, a good agreement is obtained between results.

For the second application, we consider resonator circuits optimized by the genetic algorithm [8] included in WR90 waveguide (a = 22.86 mm, b = 10.16 mm) The TE01 mode is used as excitation and the iterative process is stopped after 200 iteration. This circuit is used as a filter. Two different configurations of the filter are used. Figure 6 show the first form of the filter. The transmission parameter is depicted in Figure 7. As shown in Figure 7, the WCIP results are in agreement with published data [11].

The second example is represented in Figures 8 and 10 and its response is depicted in Figures 9 and 11. In this figures, the WCIP results are compared to those of

published data [11]. Then, we can conclude that the two results are agreed in pass band.

All over this paper, the Wave concept Iterative Method has been outlined and used to study a complex Frequency Selective Surface. A simple FSS structure and two complex are studied. The comparison of our simulated data with those from commercial code and recent published data allowed the validation of the proposed method.