In photonics technology, there’s an important sub-branch, called Plasmonics [1]-[5]. Plasmonics, as an alternative platform for manipulating and redirecting electromagnetic waves on metal surfaces [2] [4], is based on surface Plasmonpolaritons (SPPs) [3] [6], where the light coupled with electrons in metal-dielectric interface [7].

Because of overcoming the conventional optical diffraction limit and manipulation of optical wave in nano- scalefield [8], SPPs have the potential for realizing highly integrated optical circuits [9]-[11]. Many applications can be found in this area. For instance, optical sensors [12], bend waveguide devices [13], wavelength de-mul- tiplexers [14], filters [15], plasmonic switches and amplifiers [14]-[16], nano-wires, slow light devices [17], etc… .

Electromagnetically Induced Transparency (EIT) is the result of quantum interference in a three-level atomicsystem [7] [15]. The Plasmon Induced Transparency (PIT), is a plasmonic analogue of EIT [17]. The main characteristics of PIT lie in the appearance of a sharp and symmetric transparency window within absorption band, along with extraordinary steep dispersion and a dramatic reduction in group velocity [8] [18]. In this study, two designs have been proposed to display PIT in plasmonic nano-structures. Among those designs, the resonators side coupled to the metal-dielectric-metal (MDM) waveguide are of special interests, since the PIT effect can be realized in plasmonic integrated circuits [19]. In this paper, we’ve tried to design, simulate and analyze (1*1) and (1*2) MDM single ringresonators proposed slow light devices.

After this introduction section, in Section 2, we’ll have events analysis in plasmonic resonators, in which we’ll describe in details the structure of our proposed circular metal-dielectric-resonator in micron scale. The theory has been reviewed in Section 3. Simulation results of two different proposed slow light devices will be reported in Section 4. We’ll also have a conclusion section.

Induction plasmonic modes creates transparency in structures to reduce speed of light (signal). For induction creation, secondary powerful light (pump) is used for stimulation of plasmonics modes formation and deceleration of signal light in waveguide [15]-[20].

Figure 1 demonstrate a simple schematic for plasmon waveguide loaded with dielectric [20]. This plasmanic structure includes a dielectric waveguide with height (h) and width (w) on a metal layer with thickness of (G).

Dielectric layer adjacent to the metal layer can be formed prerequisite for ensuring plasmonic modes there.

Dielectric material in this study is called PMMA with a refractive index close to (n = 1.4) [21]. The layer made from gold or silver that can be selected depending on dielectric material as well as manufacturing conditions.

Other metals such as copper and aluminum as used in conventional electronic and photonic integrated circuits, may also be used [21]-[23].

In conventional photonic ring resonators, basically, two waveguides exists. One for straight waveguide at aside of circular (loop) waveguide. The cross sectional dimensions of waveguides are proportional to light wavelength. We’ve used this concept for designing a plasmonic waveguide resonator in the field of integrated slow light plasmonic device. In Figure 2, the configuration of a plasmonic MDM resonator is shown.

Figure 2 shows basically, a proposed structure for plasmonic waveguide ring resonator. A combination ofplasmonic waveguide loaded with dielectric polarization surface plasmon is designed in micrometer scale. Ascan be seen, a ring plasmonic waveguide is located in close proximity to a straight waveguide [24]. Perfectly circular ring-shaped waveguide with radius R = 5500 nm formed a ring oscillator. The minimum distance between the dielectric two straight and circular waveguide at the contact site in the zero point, assumed to be 159 nm. This distance can be varied depending on the waveguide design. Metal-dielectric-metal plasmonic waveguides has dimensions transverse profile w × h = 600 * 600 nm², and integrated gold metal film thickness G =

100 nm. Beam waveguide ring oscillator according to the desired operating frequency range of all-optical wave length λ = 1550 nm equal R = 5500 nm is considered. The light wave as a pump for exciting the environment and create transparency in the proposed structure is used. In this study, the imaginary part of the refractive index, real part of the refractive index and slow rate of change in film thickness of metal in a metal-dielectric-metal waveguide system are estimated. The change in the radius of the ring resonator, the electromagnetic wave in this element will have a direct impact on the response of slow light device [25] [26].

SPPs, are surface electromagnetic modes that propagate at the interface of a dielectric with real electic permittivity and a metal with negative permittivity. According to Drude model, we’ll have:

In the above formula, ω is the angular frequency, ω_p = 1.38 × 10¹⁶ Hz, is bulk plasmon frequency and γ_p = 2.73 × 10¹³ Hz is loss absorption coefficient [7] [27]. We know that the surface plasmon polariton waves do not propagate in TE mode. There is only TM waves that can be published in plasmonic structures.

Therefore, using the governing equations for electromagnetic waves at the interface between the metal-dielec- tric interface in accordance with the continuity equation, the following relations are required:

Complex wave vector of surface plasmon polaritonin metal-dielectric-metal waveguide with width of W is defined on the basis of the value of the effective refractive index [28].

where, is the wave vector in free space and ε_d and ε_m are permittivity for dielectric and metal constant, and k_d is the transverse wave number in the dielectric core and k_m is the transverse wave number of metal cladding [‎27]-[29]. So we’ll have:

In the specific area of frequency, using the following formula, metals, are the most absorbent.

Applying the Bear’s Law of attraction implies that for some low frequencies, the field penetrates with a factor of into metal where is skin depth. In low-frequency behavior according to the Boltzmann transport

equation, it suggests that the above description is valid until that the average electron distances are that is Fermi velocity [10] [22]. At room temperature, for conventional metals and therefore the free electron model justifies [28].

From Equation (7) we can quantitatively and clearly the forming of PIT phenomenon: as incident optical waves transmit into this system. The coupling coefficient between the two ways in our design is denoted by γ. The small nanodisk coupled to a waveguide for d = 159 nm, can be treated as an oscillator and the cavity mode decays equally into the propagating waveguide, β is the coupling coefficient between them. is the resonant

frequency of the nanodisk.. ω stands for the frequency of the incident light [28] [29].

Signal Transmission T, as a function of variations of refractive index is depicted in Figure 3. This diagram is according to our proposed circular metal-dielectric resonator structure. “S” and “L”, are electromagnetic wavesspreading through straight and ring waveguides [17] [23].

This paper presents numerically-conducted study around two new MDM-based plasmonic ring resonators in field of slow light to be designed and investigated. The proposed compact configuration as a symmetric and non-symmetric waveguide-structure is engineered.

In general, using plasmonic waveguides as alternatives for photonics devices that have been designed and built based on conventional dielectric waveguides have the advantage of obtaining much smaller sizes (up to several thousand times smaller).

However, their advantage at the expense of effective distance publish or in other words increase the release will be casualties. The wavelength of the incoming light wave as a signal in this investigation is considered to be equal to 830 nm and also transparent to pump wavelength of 1550 nm affecting the proposed structure is calculated. Plasmonic devices, propose higher speeds with lower density and power consumption than their photonic or electronic counterparts. As a result of investigations, the effects of PIT in the ring resonator design of the waveguide system with MDM, showed good agreement between transport phenomena and dispersion in the window transparency. SDF obtained at two proposed design are estimated to be more than 35.

Finally, diffusion constants derived for a system indicated that in the transparency of the window, the proposed structure can be easily adjusted by changes in metal film thickness. We also found that the resonance quality factor, can effectively adjust the dispersion relation. These plasmonic systems can be used as a hight performance filter. The default settings are made in fundamental research and applications for building integrated plasmonic devices useful. These novel plasmonic systems have important potential applications in optical nonlinearity enhancements, all-optical signal processing applications, optical communication and nonlinear devices.

The authors would like to thank their colleagues in P.R.L of Amirkabir University of Technology (AUT) for their cordial support.

Mehdi Hassani Keleshtery,Hassan Kaatuzian,Ali Mir, (2016) Analysis and Investigation of Slow Light Based on Plasmonic Induced Transparency in Metal-Dielectric-Metal Ring Resonator in a Waveguide System with Different Geometrical Designs. Optics and Photonics Journal,06,177-184. doi: 10.4236/opj.2016.68B029