During the last few decades, the impact on environment by the petroleum based transportation has driven towards electric motor based transportation. The electric vehicle [1] - [3] differs from the petroleum based vehicles in the sense that the electrical energy consumed by the electrical motor [4] can be generated by means of various and wide range of sources like nuclear energy, renewable energies and also from fossil fuels. The electrical energy then may be stored in any forms like super capacitors or batteries.

Hence due to the increased interest on the electric vehicles, the studies and researches are also growing in the area of energy storage systems [4] , bi directional dc-dc converter [2] and uninterruptible power supplies [5] [6] (Figure 1). Conventionally, the dual active bridge converter [7] was used for this application, but this converter cannot achieve zero voltage switching [8] in varies range of load variations when input and output voltage rises. Hence to eliminate this problem in control system the phase shift [9] [10] was introduced with the pulse width modulation.

Also a bidirectional dc-dc converter [11] - [13] is realized by a current fed inverter on the low voltage side of the transformer and voltage fed inverter on the high voltage side of the transformer [14] - [16] . But all the conventional converters are pertaining to the dissatisfactions in terms of switching loss and inability to achieve zero voltage switching during wide load variations. The drawbacks in the above said conventional types are eradicated in the proposed resonant based bidirectional dc-dc converter.

The proposed system consists of two full bridge bidirectional current source class-E converter (Figure 2). A transformer with secondary to primary turns ratio K_T transforms the energy between two converters. Since the low voltage side converter transistors are controlled, the converter operates as a class-E boost converter [17] and the high voltage side converter operates as a class-E rectifier with transistor body diode since it is not controlled. The combination made by inductance L_r, capacitance C_L and capacitance C_H, becomes a resonance circuit.

Likewise when the power flow takes place from V_H to V_L, the HV side converter operates as a class-E buck converter [18] . Since they are controlled and as the LV side converter transistors are not controlled, the converter acts as a class-E rectifier. Now the resonance circuit is formed by the capacitance C_L and the inductance L_r. In order to realise the Zero Voltage Switching (ZVS) in a class-E resonant converter, it has to be controlled by a frequency change by keeping a constant break between the switching pulses of the transistor as in the case of quasi resonant converter. Both the LV side boost operation and HV side buck operation are characterized by an overlap or break of control pulse of the transistor pairs located diagonally in the bridge.

A maximum power is transferred during LV boost motoring mode at the optimal operation point whereas a minimum power is transferred during the HV side. The main criteria in designing this converter are the calculation of capacitors in LV and HV side of the bidirectional current DC boost converter.

Simulation is carried through Matlab/Simulink software with an aid of Sim-Power System block sets. Modelled simulation is solved through ode 25 tb solver with 2 µs of discrete sample time in power Graphical User Interface (GUI) settings. A complete simulation model of a proposed system is shown in Figure 3. Dual full bridge was constructed by use of MOSFET from Sim-Power System block set with parallel capacitors to form the resonant tank circuits. Also a battery and PMDC motor are modelled form Sim-Power System block sets.

The proposed system is simulated by using the following specifications: Battery source V_L = 12 V, HV side of PMDC motor on 150 V dc with 2.5 Hp. Control frequency range of 200 kHz. Shunt capacitors for LV side C_L = 40 nF and the shunt capacitors for HV side is C_H = 3.5 nF. The values of the capacitance are decided based on the Equations (4) and (5).

Parasitic inductance causes oscillations in the transistor current waveforms. Simulation is modelled over 20 sec, in which first 10 sec for motoring mode by applying position torque. After 10sec load torque is changed into negative sign. Hence the machine is work as a generator and charge the battery by buck mode. The simulation result of load voltage shown in Figure 4, which shows that the energy transferring is taking place from the battery source to the load for a period of 10 sec because the V_L is less than 150 V. Hence the power flow from left to right and the load current and torque are in positive sign during this period. During this period, battery works in discharging mode and the PMDC works in motoring mode.

The 2.5 Hp load consumes the current 2.5 amps and motor reaches the rated speed of 1500 rpm as shown in Figure 5 and Figure 6 respectively during the period of motoring mode (0sec to 10 sec). During this motoring mode the load torque is maintained at 2.5 N-m as shown in Figure 7.

Similarly the simulation results are represents the charging mode (buck operation when machine work as a generator) when the back emf is greater than 150 V dc (Figure 4), during above the rated speed (Figure 6) and the energy transferring is taking place from load to battery for a period of 10sec to 20sec. During this period battery gets charged, which can be identified by the direction of the current flowing from load to battery (negative sign) as shown in Figure 5 and also the torque goes negative as shown in Figure 7.

During the motoring mode, the battery delivers a constant voltage of 12V to the load through boost converter and current also maintained a rated value for 2.5 HP load for a period up to 10sec as shown in Figure 8 and Figure 9. Figure 10 show the State Of Charging (SOC) of a battery which discharge the power and hence the SOC is start to reducing from 0sec to 10sec of motoring mode. During the buck mode, battery gets charged by 14volt and battery current goes negative for a period of 10sec to 20sec as shown in Figure 8 and Figure 9. Figure 10 show the SOC is increased due to charging of battery during the buck mode for 10sec to 20sec. The performance of the battery is validated by simulation results.

The Zero Voltage Switching (ZVS) for the converter is achieved due to the capacitors C_L and C_H. Figure 11 illustrates switching performance during resonance conditions. The switch S₂ is turned ON at 0.015sec as shown in Figure 11(a) voltage across the switch is maintained at zero as shown in Figure 11(b). At the starting time the current in the switch is zero (Figure 11(c)) and starts rising over the time. Power frequency is limited by the availability of isolated transistor drivers for bridge systems. This research work introduces and verifies the idea of application of class-E converters for bidirectional power flow.

The prototype hardware of the proposed method experimental setup implementation block diagram is shown in the Figure 12. LV-boost converter and HV-buck converter are implemented by using IRF630 transistor. A toroidal core transformer is used to link the LV and HV converter. The propylene capacitors for C_H = 3.5 nF and C_L = 40 nF is used to make resonant tank. A 12 V battery is used to store the energy available during charging and deliver the power to motor during motoring mode.

A 150 V, 2.5 Hp PMDC motor is connected in with HV side of converter. Required gate pulses of the transistors are generated from PIC16F877A microcontroller. The gate pulses are in the amplitude of 5V TTL, hence they are magnified through individual gate drivers and they are separated by isolators. A Digital Storage Oscilloscope (DSO) is used to observe the real time performance of the battery, motor and converters. Figure 13 show the photo snap of the experimental implementation setup.

Special arrangements are made for every measurement to observe DSO while hardware is running. Motor voltage and current are shown in Figure 14. Motor voltage and current are observed through attenuation probe and shown in channel-1 for 100 V/div and channel-2 for 10 A/div respectively. Time of the DSO shows 2 sec/div, hence upto first 10 sec performance shows motoring mode after 10 sec to 20 sec shows charging mode. Figure 15 shows experimental result of motor speed. The motor speed is measured through tacho generator and the speed equivalent voltage generation is observed through attenuation probe of DSO. Channel-1 of speed measurement shows 1250 rpm/div for both motoring and charging mode.

The battery performance of the experimental implementation is shown in Figure 16 for both battery voltageand current observed from attenuation probe of DSO. Channel-1 shows 10V/div of battery voltage and chan-

nel-2 shows 125 A/div of battery current. From the observation after 10 sec, battery voltage is increased in to 14 V and the current is turned into negative to charge the battery.

Soft switching performance (ZVS) of the converter is analysed by observation of gate pulse of the switch and the corresponding voltage and current of the switch. Figure 17 show the gate pulse of the switch which is generated from PIC micro controller and hence it is in the amplitude range of 5 V TTL (5 V/div) and switching frequency of 200 kHz. Respective voltage across the switch is shown in Figure 18 which shows the voltage (90 V/div) across the switch is zero when the switch is triggered and turned off. Figure 19 shows the current flow (0.5 A/div) through the switch when it’s triggered and turned off. From the observation of the obtained experimental results, they are similar in every manner with the simulated results hence the hardware implementation is validated.

The proposed BDC has many distinguished features like simple topology and reliable control strategy. Additionally with BDC the ZVS for all the switches and soft commutation for the rectifier diode over a wide load range can be easily achieved. As a result the power loss problem and the diode reverse recovery problem are resolved even for high power applications with greater efficiency. The experimental results demonstrate the validity of the simulated analysis.

Kuppan Senthil,Dr. Daniel Mary, (2016) A Resonant Dual Full-Bridge Class-E Bidirectional DC-DC Converter for Fuel Cell Electric Vehicle. Circuits and Systems,07,3392-3402. doi: 10.4236/cs.2016.710289