Low-Emissivity Hybrid Insulation is a multilayer product consisting of layers of aluminum foil and a honey- comb structure produced from polyethylene foam. The resulting structure creates reflective airspaces within the cavity that reduce radiant heat transfer and heat flow by convection. The use of aluminum foil ensures a minimum 95% reduction in radiation across the enclosed regions.

Low-Emissivity Hybrid Insulation has a foil surface emissivity of 0.04 with enclosed air cells between foils. Its core material is polyethylene foam with 35 times expansion, which is expanded to make air cells. The enclosed air cells with foil reduce convective and radiative heat transfer [1].

Figure 1 shows a 20 mm-thick Low-Emissivity Hybrid Insulation structure.

As Low-Emissivity Hybrid Insulation is not a homogeneous material, it is impossible to measure its thermal conductivity. Its insulating performance is measured by a Hot Box Test in accordance with ISO 8990 (Thermal Insulation-Determination of steady-state thermal transmission properties-Calibrated and guarded hot box).

It is necessary to verify the thermal resistance of its constitution materials to improve the insulating perfor- mance of Low-Emissivity Insulation.

This paper discusses the insulating characteristics of Low-Emissivity Hybrid Insulation depending on heat transfer paths and materials. Low-Emissivity Hybrid Insulation is composed of separated reflective air cells and polyethylene foam partitions between low-emissivity aluminum foils as shown in Figure 1. This means that Low-Emissivity Hybrid Insulation is divided into two parts according to the heat transfer paths such as reflective

air cell and conductive polyethylene foam. Comprehensive thermal transmittance tests were conducted for the Low-Emissivity Hybrid Insulation of specimens of various thicknesses. The thicknesses of the specimens were 10, 20, 30, 40, 50, 60, 80, and 100 mm. Based on the test results, its insulation-affecting factors were in-vesti- gated using a trial-and-error method.

To verify the high efficiency of Low-Emissivity Hybrid Insulation, it was tested by an accredited laboratory designated by the South Korean government. Comprehensive thermal transmittance tests were conducted for the Low-Emissivity Hybrid Insulation of specimens of various thicknesses. The thicknesses of the specimens were 10, 20, 30, 40, 50, 60, 80, and 100 mm. The comprehensive thermal transmittance test was conducted in accordance with ISO 8990 (Thermal Insulation-Determination of Steady-State Thermal Transmission Properties-Ca- librated and Guarded Hot Box). Figure 2 shows a drawing of the test specimen.

The test specimen size is 1500 mm × 1500 mm. Figure 3 shows the locations of the temperature sensors.

To get more accurate measurement results, three temperature sensors were located at each point. The temperature at each point was determined by averaging the three measured values.

The hot box facility was calibrated using a polystyrene foam board whose thermal conductivity had been acquired from a heat flow meter apparatus test at an accredited laboratory designated by KOLAS, the South Korea Laboratory Accreditation Scheme.

Tests were conducted with a hot region temperature of 20˚C and a cold region temperature of 0˚C. The heat flow rate from the hot region to the cold region is determined from energy input to the hot region as in the case with ASTM C 1363. The overall thermal transmittance was calculated after steady-state conditions had been achieved. Data were recorded three times every hour and averaged. The overall thermal transmittance (U) can be obtained from Equation (1) [2].

U: Overall thermal transmittance (W/m²∙K).

R: Overall thermal resistance (m²∙K/W).

Q: Supplied heat (W).

Th: Temperature of hot region (˚C).

Tc: Temperature of cold region (˚C).

A: Area of specimen (m²).

Test results are shown in Table 1.

Table 1 shows that a 100 mm thick Low-Emissivity Hybrid Insulation can meet the overall thermal transmittance of walls and roofs of Passive Houses which is below 0.15 W/m²∙K [5].

Figure 4 shows the required thickness of various insulations to meet the overall thermal transmittance of

Passive Houses of 0.15 W/m²∙K.

While as thick as 240 mm of EPS, whose thermal conductivity is 0.036 W/mK, should be used, as thick as 30 mm of Enervac, which is a kind of a vacuum insulation panel, can be used as insulation for Passive Houses [6]. From Table 1 and Figure 4, we can assume that Low-Emissivity Hybrid Insulation has the same insulating performance as Aerogel.

Table 2 shows required U-values for central region by South Korean building insulation codes [7].

Table 2 indicates that required U-value for exterior wall adjacent to outside directly should be less than 0.36 W/m²∙K. For the designer’s convenience, the building insulation codes provide the required insulation thickness according to each insulation grade. Table 3 shows the required thickness of insulation to obtain the required U-values.

The insulation grade is given as A, B, C, D according to thermal conductivity of insulation.

Table 4 shows how the grade is determined.

Table 4 indicates, for example, that XPS, Neopor, PU and high-density Glass Wool belong to Grade “A”.

According to Table 3 and Table 4, Existing insulations should be used as thick as 85 mm or 100 mm for an exterior wall which is adjacent to outside directly for central region in South Korea.

On the bases of the test results in Table 2, 30 mm or 40 mm Low-Emissivity Hybrid Insulation can meet the required U value for the same wall. This means that the thickness of Low-Emissivity Hybrid Insulation required to meet building codes is less than that of many competing insulations.

Low-Emissivity Hybrid Insulation is getting to be used more and more buildings such as schools, government offices, residential buildings and commercial buildings in South Korea. It is usually applied on the reinforced concrete walls and roofs as thick as 60 - 80 mm. It is unusually used as main insulation for a building in South Korea. Recently, Low-Emissivity Insulation with fire-retarding property has been developed and used as exterior insulation for large buildings above 6 stories.

Figure 5 shows various building applications of Low-Emissivity Hybrid Insulation in South Korea.

This work was supported by the National Research Foundation of South Korea (NRF) and the grant funded by the South Korea government (MEST) (No. 2014R1A1A4A01005565).

Young Cheol Kwon, (2016) Applications of Low-Emissivity Hybrid Insulation in South Korea. Journal of Power and Energy Engineering,04,8-14. doi: 10.4236/jpee.2016.47002