Electrical resistivity method was used to assess groundwater potential and vulnerability of overburden aquifers at Onibu-Eja active open dumpsite, Osogbo, Southwestern Nigeria. Eighteen Vertical Electrical Sounding (VES) points and five 2-D imaging profiles established in five traverses at the periphery of the dumpsite were surveyed and analysed. The subsurface comprised of thin topsoil (resistivity 65 - 998 Ωm); heterogeneous weathered layer with resistivity 63 - 333 Ωm and thickness 0.7 - 8.5 m; weathered basement (resistivity 31 - 1253 Ωm and thickness 0.7 - 27.0 m) and fractured/fresh basement (resistivity 36 - 6213 Ωm). The 2-D inverse model of the profiles delineated low resistivity values ranging from 5 to 100 Ωm at a depth range of 10 - 20 m along traverses TR1-TR3 which is attributed to leachate percolation close to the dumpsite. The weathered basement was inclined relative to the dumpsite. The total overburden thickness varies from 6.9 to 33.7 m, with 20 and 40 m generally recommended as productive for groundwater abstraction in Southwestern Nigeria occurring in 61% of the area. Further, about 85% of the weathered layer resistivity values fall within medium groundwater potential (100 - 250 Ωm) and high groundwater potential (>250 Ωm). The ranking of groundwater potential as a function of saprolite (weathered basement) resistivity showed that 72% of the study area is characterized by optimum weathering (20 - 100 Ωm) and is classified as good groundwater potential. Fractured basement covered <30% of the study area. The evaluation of aquifer protective capacity has helped to classify the area into moderate, weak and poor protective capacities with moderate protective capacity zone covering 72%.
The city of Osogbo and its environs in southwestern Nigeria are experiencing population growth and urbanization with its resultant pressure on the natural resources including both land and potable water supply. The state owned water board supplies water sourced and treated from the major river (River Osun). The water supply is grossly inadequate and some people rely on open surface water close to them. Groundwater that approximately 50 percent of the world’s population uses every day [1] becomes another alternative means of water supply.
Osogbo area lies within the Precambrian basement complex terrain of southwestern Nigeria [2] . Exploration of groundwater in hard rock terrain is a very difficult task when the favorable groundwater zones are associated with fractured medium. In this environment, the groundwater potential hinges mainly on the thickness of the weathered/fractured layer overlying the basement [3] . According to [4] , the overburden materials have high porosity, contain a considerable amount of water and exhibit low permeability due to its relatively high clay content. Aquifers in this basement terrain often occur at shallow depths, thus subjecting the water within to environmental hazard, susceptible to surface or near-surface contaminants. The major threat facing groundwater is pollution and degradation due to human activities, which has made fresh water scarce [5] . One of the most common sources of water pollution is dumpsites, whether landfill or open dump. Some dumpsites that were sited far from city centre are now being habited because of urbanizations. An example of such dumpsites is the Osun state main active open dump, Onibu-Eja Dumpsite, Osogbo (Figure 1(a) and Figure 1(b)) with residential buildings some few meters away.
The aim of this study is to use electrical resistivity method to delineate the groundwater aquifers, identify contamination zones and recommend appropriate points for groundwater abstraction. Electrical resistivity method using Vertical Electrical Sounding (VES) has been employed in groundwater over the years to characterize aquifers in different geologic environments and to map fractures in basement areas [6] - [10] . However, VES
(a) A section of the Onibu-Eja active dumpsite and (b) an uncompleted house approximately 5.0 m distance from the dump which forms the problem associated with the site
produces 1-D model of the subsurface, which is not sufficient in mapping areas of complex subsurface geology. The basic sounding interpretation assumption of horizontally stratified earth model, which does not match the local geological model, is the major limitations of these methods [11] . The VES is complemented with Electrical Resistivity imaging which provides 2-D resistivity model of the subsurface, where resistivity changes in the vertical as well as in the lateral direction along the traverse are mapped continuously even in the presence of geological and topographical complexities [12] . 2D electrical resistivity imaging has been employed successfully in bedrock detection, geological mapping and groundwater investigation [13] [14] .
2. Study Location and Geology
Osogbo is located between latitudes N07˚45.505' and N07˚48.552' and longitudes E04˚29.611' and E04˚34.321' (Figure 2(a)). The geology of the study area can be explained within the context of the geology of the Precambrian basement complex of southwestern Nigeria which form a part of the basement complex of Nigeria [2] [15] . The basement complex is one of the three major litho-petrological components that make up the geology of Nigeria. The major metamorphic rock types discovered around the study area, Osogbo, Southwestern Nigeria are quartzite and banded gneiss (Figure 2(a)). The quartzite found was highly fractured and outcrops as a massive ridge in the southern part of the area (Figure 2(b)). The mineralogy of the quartzite was mainly quartz with little mica. There were presences of various structures on the quartzite which include: fracture and foliation. The structures found in banded gneiss rocks were banding and joints. The joint strike directions are S172SE, E120SE, E120SE, E128SE, E110SE, and the dip 80˚NE. The area is part of Osogbo Metropolis and being a State capital has witnessed rapid growth in population. Figure 3 shows the base map of the active open dumpsite long Osogbo-Iwo highway. It was located using eTrex Legend, Garmin, Global Positioning System (GPS) with map datum at Minna, Nigeria. The X and Y axes show the easting and northing respectively. The dumpsite is accessible through a motorable path from the major highway. The dumping of waste started around 1992 and there was no engineering work on the site, which makes it purely an open surface dump. Although there is no record of the total tonnage of waste from inception, the estimated dimensions show that the dumpsite holds about 152 metric tons of waste. The area is characterized by many rivers flowing NW-SE and discharging into river Osun. The area is characterized by the tropical rain forest. The temperature ranges from 19˚C to 34˚C with an annual mean temperature of about 24˚C. The average rainfall is about 350 mm [16] . Leachate forms when rain falls and permeates through the waste dump, and can infiltrate across the unsaturated zone and transfer contaminated water to the aquifer.
3. Materials and Method of Study
Five traverses were established in W-E and S-N directions covering lateral distance between 105 to 240 m at the periphery of the dumpsite (Figure 3). The geophysical resistivity data was acquired with the Ohmega d. c. resistivity meter. Profile imaging, using dipole-dipole array, were surveyed along the traverses at inter-electrode spacing of 5 m and expansion factor (n) varied from 1 to 5. The resulting apparent resistivity data was input into the DIPROFWIN software to obtain pseudosections. Inversions were run on the pseudosections to obtain theoretical data pseudosections and a 2D resistivity structure of the subsurface. The processed 2-D resistivity structure guided the location of vertical electrical sounding points. The Schlumberger array was adopted and eighteen VES points were carried out along the five traverses in W-E and S-N directions (Figure 3). The electrode spread of AB/2 was varied from 1 to 65 m. The electrical resistivity data was processed by plotting the apparent resistivity values against the electrode spread (AB/2). This was subsequently interpreted quantitatively using partial curve matching method [6] and computer assisted 1-D forward modelling with WinResist 1.0 version software [17] . Maximum information about the subsurface lithology and overburden thickness was generated.
The combination of the resistivity and thickness in the Dar Zarrouk parameter may be of direct use in aquifer vulnerability studies [18] . The aquifer protective capacity characterization is based on the values of the longitudinal unit conductance of the overburden rock units in the area. The longitudinal conductance (S) of the
overburden at each station was generated from the equation:
.
where hi is the layer thickness, ρi is layer resistivity while the number of layers from the surface to the top of aquifer varies from i = 1 to n. The various “randomly” distributed data were gridded at 10 m cell size (about half
(a) The simplified geology map of the study area showing road network and some geological features; (b) A massive outcrop of quartzite with joints which is one of geological feature in the study area.
Data acquisition map of the study area showing locations of the traverses (Tr) and VES points (V)
the nominal data point interval) in the universal traverse Mercator co-ordinate system using an iterative program based on the minimum curvature technique with tension [19] . Minimum curvature can cause undesired oscillations and false local maxima or minima, and use of tension (T > 0) helps to suppress these effects. They were then contoured at different intervals depending on the variables.
4. Result and Analyses
The results are discussed under geoelectric sections, 2-D resistivity structure, and evaluation of groundwater potential in terms of overburden isopach map and isoresistivity maps and aquifer protective capacity (evaluation of aquifer vulnerability). The resistivity sounding curve-types acquired from the surveyed area range from 3-layer (H) to 4-layer (KH) or 5-layer (HKH). Figure 4(a), Figure 4(b) are typical 1D resistivity curves of sampled VES stations showing observed apparent resistivity, calculated apparent resistivity and computed model. Summary of the formation of layer parameters and classification of the resistivity sounding curves is presented in Table 1. These type-curves, H, QH, KH and HKH can be interpreted in terms of the subsurface lithology (e.g.
(a) Typical resistivity field curves of sampled VES stations showing H-curve; (b) Typical resistivity field curves of sampled VES stations showing KH-curve.
Summary of the geoelectric parameters over the study area
VES NO
NO of layers
Curve Type
Resistivity of layer (Ωm)
Thickness of layers (m)
Depth to basement
Longitudinal conductance (mhos)
ρ1
ρ2
ρ3
ρ4
ρ5
h1
h2
h3
h4
1
4
QH
805
333
54
398
0.5
1.6
9.1
11.2
0.174
2
4
KH
179
258
136
16213
0.4
6.0
24.2
30.6
0.203
3
5
HKH
119
73
271
31
6555
0.4
3.7
4.4
13.6
22.1
0.509
4
4
KH
168
243
52
5648
0.4
3.0
19.3
22.7
0.386
5
4
QH
127
108
49
7182
0.5
7.9
19.2
27.6
0.468
6
5
HKH
161
78
212
54
7107
0.5
2.8
3.4
27.0
33.7
0.555
7
4
KH
97
161
62
8618
0.5
5.1
22.5
28.1
0.400
8
5
HKH
227
91
210
47
2824
0.6
3.5
3.8
14.6
22.5
0.370
9
4
KH
114
151
43
4993
0.4
2.8
24.0
27.2
0.580
10
4
KH
65
69
65
5128
0.5
3.2
19.8
23.5
0.359
11
3
H
143
70
3106
0.9
18.5
19.4
0.271
12
3
H
132
44
245
1.0
9.0
10.0
0.212
13
5
HKH
219
52
161
54
1593
0.5
3.1
4.9
16.5
25.0
0.398
14
3
H
299
83
2581
0.7
23.9
24.6
0.290
15
4
HK
269
57
252
39
0.5
6.5
9.8
16.8
0.155
16
4
HK
280
63
579
145
0.5
1.2
6.0
7.7
0.031
17
4
HK
755
176
523
240
0.6
2.1
4.2
6.9
0.021
18
4
HK
998
126
1253
36
0.8
6.3
3.0
10.1
0.053
[20] [21] ) and are often associated with groundwater possibilities [22] . The nature of the lithologic sequence in a place can be used in qualitative sense to evaluate the groundwater prospect of an area [23] .
4.1. Geoelectric Sections
The interpreted VES results were used to prepare 2-D geoelectric sections which show respective layer resistivity values and thicknesses (Figures 5(a)-(d)). The sections were prepared according to the number of VES points in each traverse. It helps to see clearly where there is thin overburden as well as thick overburden within the sounding locations. The geoelectric sections presented showed three-to-five subsurface layers which include the topsoil, clay/weathered layer, partly weathered basement/weathered basement and fractured/fresh basement.
A maximum of three-to-five subsurface geoelectric units were delineated beneath VES points along traverse TR1 (Figure 5(a)). These include the topsoil (resistivity and thickness range of 119 to 805 Ωm and 0.4 to 0.5 m respectively) which overlies the weathered layer which has resistivity and thickness which vary from 243 to 333 Ωm and 1.6 to 6.0 m respectively. The weathered layer is indicative of sand. Clay with resistivity value of 73 Ωm and thickness of 3.7 m was delineated under VES point 3. The weathered basement has unsaturated clay/ sandy clay of resistivity between 31 and 136 Ωm and thickness between 4.4 and 24.2 m. The weathered layer/ basement constitutes the groundwater aquifer with total thickness range between 10.7 m and 30.2 m. A fractured basement with resistivity of 398 Ωm is delineated at VES point 1 and is favourable for groundwater. The most promising locations beneath this traverse are VES point 3 (approximately 58.0 m away from dumpsite) that has 3.7 m thick clay which could prevent leachate from permeating into the 18.0 m thick groundwater aquifer and VES point 1 (approximately 103 m away from dumpsite) which has lateritic topsoil that prevents run off pollutant from the dumpsite that could seep into the aquifer.
The geoelectric section B-B’ delineated four to five distinct geoelectric layers along traverse TR3 about 28.0 m away from the dumpsite (Figure 5(b)). Resistivity and thickness values in these layers range from 97 to 227 Ωm and 0.5 to 0.6 m for the topsoil; clay (VES points 6 and 8) with resistivity of 78 and 91 Ωm and thickness of 2.8 and 3.5 m; 108 to 212 Ωm and 3.4 to 7.9 m for the unconsolidated sandy clay/clayey sand sub-stratum, while the resistivity and thickness of the weathered basement varies from 47 to 62 Ωm and 9.2 to 27.0 m. The
(a) Geoelectric sections along traverse TR1 comprising VES points V1-V4; (b) Geoelectric sections along traverse TR3 comprising VES points V6-V8; (c) Geoelectric sections along traverse TR4 comprising VES points V11-V14; (d) Geoelectric sections along traverse TR5 comprising VES points V15- V18.
weathered layer and weathered basement constitute the groundwater aquifer with highest thickness of 27.0 m at VES point 6. The fresh basement has resistivity which varies from 2824 to 8618 Ωm. The proximity of this traverse to dumpsite makes the aquifer more vulnerable to contamination. However, VES points 6 and 8 could be considered as promising location for groundwater because of the presence of clay with thickness 2.8 m and 3.5 m respectively which shields the aquifer.
The geoelectric section C-C’ along traverse TR4 about 53 m away from the dumpsite consists of three to five subsurface geologic layers (Figure 5(c)). These include the topsoil, the clay/weathered layer with resistivities and thickness ranging from 52 to 161 Ω m and 3.1 m and 4.9 m; weathered basement (low resistivity varies from 44 to 83 Ω m and thickness ranges from 9.0 to 23.9 m). Fresh bedrock was delineated under VES 11, VES 13 and VES 14 while VES 12 showed fractured bedrock.
In traverse TR 5, about 103 m away from the dumpsite, the geoelectric section D-D’ has a maximum of four subsurface layers (Figure 5(d)). These include the topsoil (clayey sand/laterite) with resistivity and thickness varying from 280 to 998 Ωm and 0.5 to 0.8 m respectively which lies above the water table. Clay with resistivity between 57 and 63 Ωm and thickness between 1.2 and 6.5 m was delineated at VES point 15 and 16 while weathered layer (resistivity and thickness vary from 128 to 176 Ωm and from 2.1 to 6.3 m) is seen at VES point 17 and 18. A partly weathered basement with resistivity and thickness varying between 252 and 1253 Ωm and 3.0 and 9.8 m respectively is delineated overlying the fractured basement with resistivity range from 36 to 240 Ωm.
4.2. The 2-D Resistivity Structures Distribution
The interpreted 2-D resistivity structure sections were merged to form a pseudo-3D pattern of the resistivity map of the study area. This arrangement of the resistivity sections makes it possible to observe the distribution trend of the resistivity pattern in the study area. The subsurface resistivity in the 2-D resistivity structure (Figure 6) shows a wide variation in the rock or lithology resistivity and at different depth along the profiles. The first two layers, the topsoil and weathered layer have resistivity value ranges between 30 Ωm and 1880 Ωm with thickness varying from <2 m to about 10 m. The subsurface resistivity heterogeneity comes from the existence of clayey sand/sandy clay with lateritic clay and outcrop at traverse TR1 to TR5. The weathered basement is mostly characterized by low resistivity value ranges between 5 Ωm and 100 Ωm while thickness varies from 10 to 20 m. This is seen on part of profiles along traverse TR1 to TR3 which are closer to the dumpsite as indicated in Figure 6.
4.3. Isopach and Isoresistivity Maps of Aquifer Units in the Area
The isopach and isoresistivity maps of the study area are shown (Figure 7 and Figure 8). The thickness of the overburden and the resistivity are important hydrogeologic considerations in groundwater development in the
The 2-D resistivity structures distribution showing low resistivity zones suspected to be pollution plume
basement terrain. The reason for this is that water gets into the saturated zone through the overburden.
4.3.1. Assessment of Groundwater Potential in Terms of Overburden Thickness.
Depth to fresh basement (overburden thickness) at each VES sounding station was gridded and contoured and shown as isopach map of the overburden (Figure 7). The overburden include the topsoil, weathered layer and partly/weathered basement. The depth to fresh basement varies from 6.9 to 33.7 m. Generally, the overburden thickness is trending N-S and high overburden thickness is observed near the dumpsite and low farthest away. The map has been subdivided into four zones of high (A); medium (B); low (C) and minimal (D) groundwater potential. In Figure 7 zone A shows that overburden thickness <40 m has 11%, zone B with overburden thickness <30 m which is the most predominant occupies 50% while 28% overburden thickness for zone C is <20 m. the percentage of overburden thickness <10 m at zone D is 11%.
4.3.2. Assessment of Groundwater Potential Using Isoresistivity Maps
1) Isoresistivity map of weathered layer
The groundwater potential could also be zoned into high, medium and low potential based on weathered layer resistivity. The isoresistivity map of the weathered layer is shown in Figure 8(a). Zones where resistivity is <100 Ωm is classified as low groundwater potential, zone where resistivity ranges from 100 to 250 Ωm is classified as medium groundwater potential while zones with resistivity >250 Ωm are classified as high groundwater potential [21] . This partly or generally correlates with the overburden thickness map (Figure 7).
The weathered layer resistivity values vary from 63 to 333 Ωm. The study area is dominated by zone of medium groundwater potential (100 to 250 Ωm). This zone is interpreted to be made of sandy clay/clayey sand. Zone of low groundwater potential (<100 Ωm) has impermeable clay materials. a porous and permeable sand is
Isopach map of the overburden thickness in the study area. Almost half the area has the optimum thickness (<30 m)
indicated as zone of high groundwater potential with resistivity >250 Ωm.
2) Isoresistivity map of weathered basement
The resistivity values of weathered basement at the various VES stations occupied in the study area were contoured and presented as isoresistivity map of weathered basement (Figure 8(b)). The resistivity values range from 31 to 1253 Ωm. This indicates that the material composition is largely clay/sandy clay/clayey sand [24] - [26] .
[27] [28] developed a scheme for ranking of groundwater potential as a function of saprolite (weathered basement) resistivity as presented in Table 2. This classification shows that resistivity range 20 - 100 Ωm is related with optimum weathering and groundwater potential while resistivity range of 101 - 150 Ωm are suggestive of medium aquifer conditions and potential. When the weathered basement resistivity falls within the range of 151 - 300 Ωm, it is indicative of limited weathering and poor potential. By this classification, 72% of the study area (Figure 8(b) and Figure 9) is characterized by optimum weathering and groundwater potential with 5.5% of the study showing medium aquifer conditions and potential. Also 5.5% account for areas of limited weathering and poor potential. The weathered basement resistivity values >300 Ωm represents 17%. This region offers no appeal for groundwater development unless it is overlain by thick overburden. Region of the map that
(a) The weathered layer resistivity distribution map of the study area; (b) The weathered basement resistivity distribution map of the study area.
Aquifer potential as a function of saprolite resistivity of the study area
Saprolite resistivity (Ωm)
Aquifer characteristics
<20
Clayey; limited aquifer potential
20 - 100
Optimum weathering and groundwater potential
101 - 150
Medium aquifer conditions and potential
151 - 300
Limited weathering and poor potential
>300
Negligible
Source: Modified after [27] [28] .
Weathered basement resistivity classification of the study area
falls into clayey formation with resistivity <20 Ωm has limited aquifer potential. Again, general classifications agree with the previous overburden thickness (Figure 7) and weathered layer resistivity (Figure 8(a)) assessments.
4.4. Bedrock Resistivity Distribution Map of the Study Area
Aquiferous units in the basement complex terrain are mainly found in the thick and porous weathered overburden (saprolite zone) and the fractured part of the bedrock. The presence of these fractures further supports the groundwater potentials of those zones [26] [29] [30] . Fractures influence the groundwater yield more than weathered layer probably because of the relatively high permeability [31] - [33] . A modified aquifer potential as a function of the fractured bedrock is shown in Table 3. The fractured/fresh bedrock resistivity values of the study area vary from 36 - 16,213 Ωm (Figure 10). High fractured permeability as a result of weathering is delineated at the eastern part with resistivity values <750 Ωm, an indication of high aquifer potential. Fairly low effect of fractures is noted at the central area within resistivity range of 1501 - 3000 Ωm; thus exhibiting low aquifer potential. Over 55% of the area is underlain by fresh basement rocks with resistivities ≥3106 Ωm and this is seen at the western area, also extending to the north and south. These areas show little or no fractured bedrock; thus they have negligible aquifer potential.
4.5. Evaluation of Aquifer Protective Capacity
Aquifer protective capacity (APC) is the ability of the overburden unit to impede and filter percolating ground surface leaching fluid from entering into the aquiferous unit [35] . The aquifer protective capacity characterization is based on the values of the longitudinal unit conductance of the overburden rock units in the area. The longitudinal unit conductance (S) values obtained from the study area range from 0.021 to 0.580 mhos and were used to generate the map shown in Figure 11. Clayey overburden, which is depicted by relatively high longitudinal conductance, gives protection to the underlying aquifer. [36] - [38] classified the protective capacity of the overburden into excellent, very good, good, moderate, weak and poor protective capacity zones (Table 4). The portion having conductance values ranging from 0.2 to 0.69 mhos covered about 72% of the study area and was classified as zone of moderate protective capacity; the values between 0.1 and 0.19 mhos covered about 11% and was classified as of weak protective capacity and about 17% of the area has conductance value <0.1 mhos and was considered poor (Figure 11).
Aquifer potential as a function of the fractured bedroc
Saprolite resistivity (Ωm)
Aquifer characteristics
<750
High fractured permeability as a result of weathering; high aquifer potential.
750 - 1500
Reduced influence of weathering; medium aquifer potential.
1501 - 3000
Fairly low effect of weathering; low aquifer potential.
>3000
Little or no weathering of the bedrock; negligible aquifer potential.
Source: Modified after [28] [34] .
Bedrock resistivity distribution map of the study area
5. Discussion5.1. Subsurface Resistivity and Lithology
The geoelectric survey shows the form of subsurface resistivity variations around the dumpsite. A number of authors have attempted to correlate the typical geological sequence in basement complex terrain with resistivity ranges (e.g. [27] [34] [39] ). On this basis, three to five subsurface geologic layers were delineated which include the topsoil, clay/weathered layer, weathered basement and fractured/fresh basement. The geoelectric sections showed topsoil of resistivity and thickness values varied from 65 to 998 Ωm and 0.4 to 1.0 m; clay layer with resistivity and thickness values of range 52 to 91 Ωm and 1.2 to 6.5 Ωm. The weathered layer depicted a heterogeneous subsurface of clay/sandy clay and clayey sand with resistivity and thickness values varying from 63 to 333 Ωm and 0.7 to 8.5 m; weathered basement has resistivity of between 31 Ωm and 1253 Ωm and thickness between 3.0 m and 27.0 m. The fractured/fresh basement showed resistivity values ranging from 36 to 16,213 Ωm.
In 2-D imaging the topsoil and the weathered layers show resistivity heterogeneities which come from the
Spatial distributions of longitudinal conductance and aquifer protection capacity zones
existence of clayey sand/sandy clay with lateritic clay along traverse TR1 to TR5. The resistivity value ranges between 30 Ωm and 1880 Ωm with thickness varying from <2 m to about 10 m. The weathered basement is mostly characterized by low resistivity value ranges between 5 Ωm to 100 Ωm while thickness varies from 10 to 20 m. As mentioned earlier, the natures of the lithologic sequences, and the thickness and resistivity of overburden, are particularly important hydrogeologic considerations in assessing the groundwater potential of basement complex terrains.
5.2. Groundwater Potential
[34] proposed values of overburden thickness ranging between 20 m and 30 m for productive wells in Shaki, west of the study area. Similarly, [36] [40] also prescribed a minimum overburden thickness of 25 m for viable groundwater abstraction in similar environments. In the surveyed area, the depth to fresh basement (total overburden) varies from 6.9 to 33.7 m. Overburden thickness of between 20 m and 40 m occurred in 61% which thus suggests that the water-bearing horizon across the area is generally significantly thick and can support productive groundwater abstraction (Figure 7). In a comparable basement complex in Zimbabwe, [41] recommended a minimum of 10 m of regolith thickness to ensure sufficient yield.
According to [42] the thick weathered layer (containing less percentage of clay) above the basement rock constitutes a water-bearing layer. The weathered layer resistivity ranged between 63 Ωm and 333 Ωm with about 85% of the area falling within medium groundwater potential (100 to 250 Ωm) and high groundwater potential (>250 Ωm) according to [21] . The weathered layer in the surveyed area can only support hand dug wells because the thickness ranges from 0.7 to 8.5 m (Figure 5) which conforms to average well depth of 7.07 m in the neighbouring residential settlements [16] [43] . The weathered basement resistivity values range from 31 to 1253 Ωm with the thickness varying from 3.0 to 27.0 m. The ranking of groundwater potential as a function of saprolite resistivity [27] [28] showed that 72% of the study area with 20 to 100 Ωm is characterized by optimum weathering and groundwater potential while 5.5% of the study area with resistivity between 101 and 150 Ωm exhibited medium aquifer conditions and potential. Bedrock fractures contribute substantially to groundwater yield in a typical basement complex area. High fractured permeability as a result of weathering is observed at the eastern part with resistivity values <750 Ωm an indication of high aquifer potential. However, the fractured zone covered <30% of the study area. It is significant that the three main important characteristics, namely overburden thickness, weathered layer resistivity and weathered basement resistivity generally support one another in the groundwater potential evaluation.
5.3. Aquifer Vulnerability
The low resistivity value materials suspected to be caused by leachate from the dumpsite are seen along traverses TR1 to TR3 closer to the dumpsite. This implies that contaminant leachate plume seeped to the bottom in vertical motion to the groundwater aquifer. [44] attributed the vertical motion to the relative porous and permeability of the sandy overburden in such affected zones. Thus the groundwater aquifer close to dumpsites is vulnerable to contamination, therefore it becomes imperative to evaluate and classify the aquifer protective capacity according to previous studies (e.g. [36] - [38] ). The portion having conductance values ranging from 0.2 to 0.69 mhos covered about 72% of the study area and was classified as zone of moderate protective capacity; that ranging from 0.1 to 0.19 mhos covered about 11% and was classified as of weak protective capacity and about 17% of the area has conductance value <0.1 mhos and was considered poor. The weak and poor protective zones are prone to surface and near-surface leachate, while in the moderately protected zones, the aquifer is fairly protected from leachate percolating fluids. In the latter zones the topmost layers/weathered layer are mostly sandy, and where clays which protect the aquifer are found, they are usually very thin and hence provide little or no protection for the underlying aquifer.
5.4. Correlation of Maps
The 3D display in Figure 12 is a correlation of the various maps and helps to summarize the groundwater potential and the vulnerability of the aquifers (Table 5).
6. Conclusion
In conclusion, the factors discussed above have to be taken into consideration when sitting a hand dug well or borehole in the study area. It is, therefore, necessary that such VES position should have protective clay of thickness >2.5 m, productive overburden thickness ranging from 20 to 40 m [34] [36] [40] , and be in a porous and permeable weathered layer of medium-high groundwater potential. It is within the optimum weathering resistivity variation of 20 to 100 Ωm and moderate aquifer protective capacity. Four VES positions in Table 6 are therefore recommended based on the aforementioned factors.
3D map display and selected positions (highest values in red/purple down to the lowest values in deep blue)
Characteristics of important areas identified in the various maps (<xref ref-type="fig" rid="fig1">Figure 1</xref>2)
Parameters
A ≈ 25 m from dumpsite
B ≈ 50 m from dumpsite
C ≈ 95 m from dumpsite
Overburden
Relatively high > 2 - < 40 m. Medium/high groundwater potential
Recommended VES points for groundwater abstraction
VES NO
Clay cover resistivity (Ωm)
Clay thickness (m)
Over burden thickness (m)
Weathered layer resistivity (Ωm)
Weathered basement resistivity (Ωm)
Longitudinal conductance
Protective capacity rating
3
73
3.7
22.1
271
31
0.509
Moderate
6
78
2.8
33.7
212
54
0.555
Moderate
8
91
3.5
22.5
210
47
0.370
Moderate
13
52
3.1
25.0
161
54
0.398
Moderate
Acknowledgements
The first author sincerely appreciates Federal Ministry of Education, Nigeria for the scholarship grant and Osun State Environmental Protection Agency for granting permission to use the dumpsite. Mr. Mamukuyomi Abiodun assisted during data acquisition. He is gratefully acknowledged.
Cite this paper
Nicholas U.Ugwu,Rubeni T.Ranganai,Rapelang E.Simon,GhebrebrhanOgubazghi, (2016) Geoelectric Evaluation of Groundwater Potential and Vulnerability of Overburden Aquifers at Onibu-Eja Active Open Dumpsite, Osogbo, Southwestern Nigeria. Journal of Water Resource and Protection,08,311-329. doi: 10.4236/jwarp.2016.83026
NOTESReferencesMargat, J. and van der Gun, J. (2013) Groundwater around the World: A Geographic Synopsis. CRC Press/Balkema. Leiden.Rahaman, M.A. (1988) Recent Advances in the Study of the Basement Complex of Nigeria. In Precambrian Geology of Nigeria, Geological Survey of Nigeria, Kaduna South, 11-43.Al-Garni M.A. ,et al. (2009)Geophysical Investigations for Groundwater in a Complex Subsurface. Terrain, Wadi Fatima, KSA: A Case History Jordan Journal of Civil Engineering 3, 118-136.Barker, R.D. (2001) Imaging Fractures in Hard Rock Terrain. University of Birmingham, UK. http://www.bham.ac.uk/EarthSciences/research/hydro/envgeo/Efe S.I. ,et al. (2002)Urban Warming in Nigerian Cities. The Case of Warri Metropolis African Journal of Environmental Studies 3, 160-168.Koefoed, O.C. (1979) Geosounding Principles 1: Resistivity Sounding Measurements. Elsevier Science Publishing Company, Amsterdam.McDowell, P.W. (1979) Geophysical Mapping of Water Filled Fracture Zones in Rocks. International Association of Engineering Geology Bulletin, 19, 258-264. http://dx.doi.org/10.1007/BF02600485Ayolabi, E.A., Adedeji, J.K. and Oladapo, I.M. (2003) A Geoelectric Mapping of Ijapo, Akure South Western Nigeria and Its Hydrogeological Implications. Global Journal of Pure and Applied Sciences, 10, 441-446.Ayolabi, E.A., Folorunso, A.F., Eleyinmi, A.F., Esther, O. and Anuyah, E.O. (2009) Applications of 1D and 2D Electrical Resistivity Methods to Map Aquifers in a Complex Geologic Terrain of Foursquare Camp, Ajebo, Southwestern Nigeria. The Pacific Journal of Science and Technology, 10, 657-666.Sharma, S.P. and Baranwal, V.C. (2005) Delineation of Groundwater-Bearing Fracture Zone in a Hardrock Area Integrating Very Low Frequency Electromagnetic and Resistivity Data. Journal of Applied Geophysics, 57, 155-166.http://dx.doi.org/10.1016/j.jappgeo.2004.10.003Griffiths D.H. and Barker, R.D. (1993) Two-Dimensional Resistivity Imaging and Modeling in Areas of Complex Geology. Journal of Applied Geophysics, 29, 21-26. http://dx.doi.org/10.1016/0926-9851(93)90005-JLoke, M.H. (2000) A Practical Guide to 2-D and 3-D Surveys. http://www.heritagegeophysics.comZhou, Q.Y., Matsui, H. and Shimada, J. (2004) Characterization of the Unsaturated Zone around a Cavity in Fractured Rocks Using Electrical Resistivity Tomography. Journal of Hydraulic Research, 42, 25-31.http://dx.doi.org/10.1080/00221680409500044Roa, B.V., Prasad, Y.S. and Reddy, K.S. (2013) Hydrogeophysical Investigations in a Typical Khondalitic Terrain to Delineate the Kaolinised Layer Using Resistivity Imaging. Journal Geological Society of India, 81, 521-530.http://dx.doi.org/10.1007/s12594-013-0067-xRahaman, M.A. (1989) Review of the Basement Geology of Southwestern Nigeria. In: Kogbe, C.A., Ed., Geology of Nigeria, Elizabeth Publishing Co., Nigeria, 41-58.Oyelami, A.C., Ojo, A.O., Aladejana, J.A. and Agbede, O.O. (2013) Assessing the Effect of a Dumpsite on Groundwater Quality: A Case Study of Aduramigba Estate within Osogbo Metropolis. Journal of Environment and Earth Science, 3, 2224-3216.Vander-Velpen, B.P.A. (2004) WinRESIST Version 1.0 Resistivity Depth Sounding Interpretation Software. M.Sc Research Project, ITC, Delft, the Netherland.Henriet, J.P. (1976) Direct Application of the Dar Zarrouk Parameters in Groundwater Surveys. Geophysical Prospecting, 2, 344-353. http://dx.doi.org/10.1111/j.1365-2478.1976.tb00931.xSmith, W.H.F. and Wessel, P. (1990) Gridding with Continuous Curvature Splines in Tension. Geophysics, 55, 293-305. http://dx.doi.org/10.1190/1.1442837Olayinka, A.I., Amidu, S.A. and Oladunjoye, M.A. (2004) Use of Electromagnetic Profiling and Resistivity Sounding for Groundwater Exploration in the Crystalline Basement Area of Igbeti, Southwestern Nigeria. Global Journal of Geological Sciences, 2, 243-253. http://dx.doi.org/10.4314/gjgs.v2i2.18701Akintorinwa, O.J. (2015) Groundwater Potential Assessment of Iwaro-Oka, SW Nigeria Using Geoelectric Parameters. British Journal of Applied Science & Technology, 6, 364-377. http://dx.doi.org/10.9734/BJAST/2015/14584Omosuyi G.O. ,et al. (2010)Geoelectric Assessment of Groundwater Prospect and Vulnerability of Overburden Aquifers at Idanre, Southwestern Nigeria Ozean Journal of Applied Science 3, 19-28.Worthington, P.R. (1977) Geophysical Investigations of Groundwater Resources in the Kalahari Basin. Geophysics, 42, 838-849. http://dx.doi.org/10.1190/1.1440751Olayinka, A.I. and Olorunfemi, M.O. (1992) Determination of Geoelectric Characteristics in Okene Area and Implications for Borehole Siting. Journal of Mining and Geology, 28, 403-411.Adelusi, A.O., Ayuk, M.A. and Oyedele, A.A. (2004) Hydrogeophysical Analysis of Owode Area around Oba-Ile near Akure, SW Nigeria. African Journal of Development Studies, 4, 11-14.Mallam A. ,et al. (2004)Fresh Basement: Revealed from Resistivity Method Zuma Journal of Pure and Applied Sciences 6, 6-9.Wright, E.P. (1992) The Hydrogeology of Crystalline Basement Aquifers in Africa. Geological Society of London, Special Publications, 66, 1-27. http://dx.doi.org/10.1144/GSL.SP.1992.066.01.01Oyedele, E.A.A. and Olayinka, A.I. (2012) Statistical Evaluation of Groundwater Potential of Ado-Ekiti, Southwest Nigeria. Transnational Journal of Science and Technology, 2, 110-127.Shemang Jr. E.N. ,et al. (1993)Groundwater Potentials of Kubanni River Basin, Zaria, Nigeria from DC Resistivity Study Water Resources 4, 36-42.Aboh, H.O. and Osazuwa, I.B. (2000) Lithological Deductions from Regional Geoelectric Investigation in Kaduna, Kaduna State Nigeria. Nigerian Journal of Physics, 12, 1-7.Olorunfemi, M.O. and Fasuyi, S.A. (1993) Aquifer Types and the Geoelectric/Hydrogeologic Characteristics of Part of Central Basement Terrain of Nigeria (Niger State). Journal of African Earth Sciences, 16, 309-317. http://dx.doi.org/10.1016/0899-5362(93)90051-QBala, A.E. and Ike, E.C. (2001) The Aquifer of the Crystalline Basement Rocks in Gusau Area, North-Western Nigeria. Journal of Mining and Geology, 37, 177-184.Omosuyi, G.O., Ojo, J.S. and Enikanselu, P.A. (2003) Geophysical Investigation for Groundwater around Obanla-Obakekere in Akure Area within the Basement Complex of South-Western Nigeria. Journal of Mining and Geology, 39, 109-116.Olayinka, A.I., Akpan, E.J. and Magbagbeola, O.A. (1997) Geoelectric Sounding for Estimating Aquifer Potential in the Crystalline Basement Area around Shaki, Southwest Nigeria. Water Resources, 8, 71-81.Olorunfemi, M.O., Ojo, J.S. and Akintunde, M.O. (1999) Hydrogeophysical Evaluation of the Groundwater Potentials of the Akure Metropolis. Journal of Mining and Geology, 35, 207-228.Oladapo, M.I., Mohammed, M.Z., Adeoye, O.O. and Adetola, B.A. (2004) Geoelectrical Investigation of the Ondo State Housing Corporation Estate, Ijapo Akure, Southwestern Nigeria. Journal of Mining and Geology, 40, 41-48. http://dx.doi.org/10.4314/jmg.v40i1.18807Oladapo, M.I. and Akintorinwa, O.J. (2007) Hydrogeophysical Study of Ogbese, Southwestern, Nigeria. Global Journal of Pure and Applied Sciences, 13, 55-61. http://dx.doi.org/10.4314/gjpas.v13i1.16669Abiola, O., Enikanselu, P.A. and Oladapo, M.I. (2009) Groundwater Potential and Aquifer Protective Capacity of Overburden Units in Ado-Ekiti, Southwestern Nigeria. International Journal of Physical Sciences, 4, 120-132.Akintorinwa, O.J. and Abiola, O. (2012) Comparison of Schlumberger and Modified Schlumberger Arrays VES Interpretation Results. Research Journal in Engineering and Applied Sciences, 1, 190-196.Olorunfemi, M.O. and Okhue, E.J. (1992) Hyrogeologic and Geologic Significance of a Geoelectric Survey at Ile-Ife, Nigeria. Journal of Mining and Geology, 28, 242-350.White, C.C., Huston, J.T.F. and Baker, R.D. (1988) The Victoria Province Drought Relief Project 1. Geophysical Sitting of Boreholes. Groundwater, 26, 309-316. http://dx.doi.org/10.1111/j.1745-6584.1988.tb00394.xLenkey, L., Hamori, Z. and Mihalffy, P. (2005) Investigating the Hydrogeology of a Water-Supply Area Using Direct-Current Vertical Electrical Sounding. Geophysics, 70, 1-19. http://dx.doi.org/10.1190/1.2000288Ojo, A.O., Oyelami, C.A. and Adereti, A.O. (2014) Hydro-Geochemical and Geophysical Study of Groundwater in the Suburb of Osogbo, South Western Nigeria. Journal of Earth Science & Climatic Change, 5, 205.Ariyo, S.O., Omosanya, K.O. and Oshinloye, B.A. (2013) Electrical Resistivity Imaging of Contaminant Zone at Sotubo Dumpsite along Sagamu-Ikorodu Road, Southwestern Nigeria. African Journal of Environmental Science and Technology, 7, 312-320.