Most of the metropolitan cities of the world have heavy transportation load to complete needs of the people of the city. This load is increasing with respect to time as the population is increasing. This increasing transportation load is making it difficult to manage the health and safety of societies. There are many kinds of sources of emission like industrial, vehicular and domestic sector in the megacities but vehicular sources are at ground level source and so have severe effect on human health and environment [1] -[9] . It is important to make better and healthy environment, which requires study of vehicular pollution. The Chembur region of the Mumbai city has been selected for study of vehicular pollution. There are many ways to model vehicular pollution. The most widely used ones are Gaussian based, viz. CALINE3 model, EPA’s HIWAY-2 model and GM model [10] -[12] . The modified HIWAY model (called HIWAY-2) and the GM model are applicable to a situation where the upwind segment of the road (measured from the perpendicular line drawn from the receptor) is at least three times the distance between the receptor and the road. Hence, the GM model overpredicts the concentration by a considerable amount if the above constraint is not satisfied [13] . The above constraint can be handled by using the HIWAY-2 model but its performance is not as accurate as that of the GM model [14] . Moreover, the HIWAY-2 and CALINE3 models require rigorous computer calculations to estimate the value of integration. A model was developed by Csanady for a finite line source which is applicable for any orientation of wind with roadways [15] . All these models require meteorological data, surface characteristics and emission data of vehicles. In the present study, a new approach to vehicular pollution modelling has been attempted and compared with observed data.

Chembur is a highly polluted region by industries as well as vehicles. Its latitude and longitude are 19.05˚N and 72.89˚E respectively. The study area is 6.5 kilometres east-to-west and 8.45 kilometres north-to-south as shown in Figure 1. It contains heavy duty vehicles on Port Trust Road, Mahul Road and Ramakrishna Chemburkar Marg. Due to continuous movement of heavy vehicles, road conditions are getting worse. It has four major industries such as two refineries (BPCL and HPCL), a fertilizer (RCFL) and a power plant (TPCL). WRF model

was used to derive meteorology for input in air quality model. Nine parameters on meteorology were generated using WRF model and fed in AERMET which is preprocessor of AERMOD.

Air quality model requires two kinds of input data viz. emission data and meteorological data. Emission inventory was prepared using actual number of vehicles, respective emission factors and vehicle kilometer travelled (VKT). Vehicle counting was done for six roads of Chembur and emission inventory data was assembled with the help of air quality monitoring project―Indian clean air programme, ARAI, Pune [16] . Onsite meteorological data was generated using Weather Research and Forecasting (WRF) model for hours of month May, which saved time and resources. National Centers for Environmental Prediction (NCEP) FNL (Final) Operational Global Analysis data were used as input of WRF whose resolution were at 1.0 × 1.0 degree grids, prepared operationally for every six hours. This product is from the Global Data Assimilation System (GDAS), which continuously collects observational data from the Global Telecommunications System (GTS), and other sources, for many analyses. These meteorological data from output of WRF model were prepared in spread sheet and was fed in AERMET with preprocessor of AERMOD. Later, AERMOD model was used for prediction of NO_x and PM concentration from traffic emission for the six roads of Chembur.

In the present study, NO_x and PM emission has been modelled for the month of May, 2011 to find out the dominant source in the study domain. May month is the pre-monsoon season and it is critical like December and has high concentration of pollutant for Mumbai city. Vehicular emission varies with time of the day i.e. morning peak, evening peak, off peak and lean peak. So, vehicular emission modelling has been done to see this effect. The model results were compared with observed value of concentration [17] . Here, modelling was carried out for all the sources of the region (given Table A1 in Appendix).

Figure 2 shows the wind rose of May 2011 generated by WRF which has been used in air quality modelling of vehicular sources for the study domain for six roads. The wind rose shows that maximum period of time wind is blowing from north-west corner. The maximum wind speed is 9 m/s and minimum wind speed is 0.3 m/s. The

calm condition was 1.1% of time where 1 m/s was wind speed threshold. A very low frequency of wind is from south-west direction with wind speed around 5 m/s.

The aim of the study was to generate onsite meteorological profiles for using in vehicular pollution modelling of Chembur area. The advance WRF model was used successfully in this study. It generates onsite and real time meteorological data which is fed in AERMET pre-processor of dispersion model AERMOD. The integrated model was applied in May 2011 for all vehicular sources. The results show that contribution of NO_x concentration in total NO_x in ambient air is about 35% from vehicles. Contribution of PM concentration is very low as emission from vehicles is low. The PM result is not in a good agreement with observed data because emission inventory is taken only for vehicles. In this study, WRF model has been used successfully for prediction of air quality. It shows that the use of WRF model can save considerable cost for processing the data as compared to collecting from meteorological station.