EPEEnergy and Power Engineering1949-243XScientific Research Publishing10.4236/epe.2013.510066EPE-41253ArticlesEngineering Simulation of a DI Diesel Engine Performance Fuelled on Biodiesel Using a Semi-Empirical 0D Model laudeValery Ngayihi Abbe1*RobertNzengwa1RaidandiDanwe2ZacharieMerlin Ayissi2MarcelObounou3Department of Physics, Faculty of Sciences, University of Yaoundé, Yaoundé, CameroonFaculty of Industrial Engineering, University of Douala, Douala, CameroonLaboratory of Applied Mathematics, National Advanced School of Engineering, University of Yaoundé, Yaoundé, Cameroon;Faculty of Industrial Engineering, University of Douala, Douala, Cameroon* E-mail:ngayihiclaude@yahoo.fr(LVNA);251220130510596603October 17, 2013November 17, 2013 November 24, 2013© Copyright 2014 by authors and Scientific Research Publishing Inc. 2014This work is licensed under the Creative Commons Attribution International License (CC BY). http://creativecommons.org/licenses/by/4.0/

Diesel engines have proven over the years important in terms of efficiency and fuel consumption to power generation ratio. Many research works show the potential of biodiesel as a substitute for conventional gasoil. Mainly, previous and recent researches have focused on experimental investigation of diesel engine performance fuelled by biodiesel. Researches on the mathematical description of diesel engine process running on biodiesel are scarce, and mostly about chemical and thermodynamic description of the combustion process of biodiesel rather than performance studies. This work describes a numerical investigation on the performance analysis of a diesel engine fuelled by palm oil biodiesel. The numerical investigation was made using a semi empirical 0D model based on Wiebe’s and Watson’s model which was implemented via the open access numerical calculation software Scilab. The model was validated first by comparing with experimental pressure and performance data of a one cylinder engine at rated speed and secondly by comparing with a six cylinders engine performance data at various crankshaft rotational speeds. Simulations were then made to analyze the engine performance when running on biodiesel. The calculations were made at constant combustion duration and constant coefficient of excess air. Results showed that the model matches the overall experimental data, such as the power output and peak cylinder pressure. The ignition delay was somehow underestimated by the model for the first experiment, which caused a slight gap on in cylinder pressure curve, whereas it predicted the average ignition delay fairly well for the second set of validation. The simulations of engine performance when running on biodiesel confirmed results obtained in previous experimental researches on biodiesel. The model will be further investigated for engine control when shifting to biodiesel fuel.

Semi-Empirical 0D Model; Scilab; Biodiesel; Performance; Diesel Engine1. Introduction

Reaching lower toxicity of exhaust gases, whilst reducing fuel consumption is one of the modern trends in automobile engineering research. The characteristics of fuel play an important role in the performances of the engine. Gasoil has been for years the main fuel for diesel engine but, due to the reducing availability of fossil energy resources and the stricter rules on engine emission [1], and researchers have been investigating the use of alternative fuels. Biodiesel, which is obtained through transesterification process of vegetable oil, has been proven to be a high potential substitute for conventional gasoil [1-3].

Simulation and mathematical modeling of diesel engine are scientific topics carried out by several research works. Nowadays, there mainly exist three types of approaches for diesel engine simulation: 0 dimensional thermodynamic, quasi dimensional and multi dimensional (Computational Fluid Dynamic). A well documented discussion on these models can be found in [4].

Many commercial computer codes based on computational fluid dynamic (CFD) [5] provide useful tools to simulate in diesel engine processes. CFD permits simulating real engine conditions with the aim of understanding how physical and chemical conditions will affect engine performances. One of the main disadvantages of CFD tools is that they are too slow to be implemented in car vehicles control software and their use as optimization or simulation tools which have a very high computer cost. Car control software mostly uses semi empirical 0D model due to their simplify approach, their quickness of implementation inside the electronic unit control of the engine. For engine simulation and optimization, several commercial codes using semi empirical models exist [6, 7]. The cost for license acquisition and the access to source codes are some of the limitations of this software in term of scientific research. To get away from these limitations we used an open source numerical calculation software called Scilab [8] in which we implemented our model.

The model we implemented in our study is based on the engine performance Wiebe model [9]. It has been for years used in diesel engine simulation, and it requires adjustable experimental coefficients related to engine specification. Since the scope of the work is about defining effect of biodiesel on engine performances, the experimental coefficient can be considered constant since they don’t depend on the fuel used.

One of the limitations of the Wiebe model is that it doesn’t predict well the combustion during the premix phase of combustion. That limitation is overcome by Watson model of heat release in diesel engine [4,10]. Both Wiebe and Watson model don’t take into account the ignition delay of the injected fuel in the cylinder, thus obliging us to find a suitable relationship to predict ignition delay. Pischinger et al. [11] defined a correlation between the length of the fuel spray at which ignition occurs and the temperature and pressure at the start of injection angle. Others strong relationship between ignition delay and start of injection angle was experimentally derived by Razlejtsev [12] and Lechivskii [13]. In these relationships, the ignition delay is described using an Arrenhius correlation between the pressure and temperature at start of injection angle and activation energy of the fuel. However, these relationships don’t give a methodology to compute ignition delay for other types of fuels such as biodiesel. Most of the coefficients used in these relationships refer to experiments conducted in engine running under conventional diesel, thus leading one to the search of suited relationship which can take into account certain physical and chemical specificities of fuel used.

The present work, describes a semi empirical model used to predict how performances parameters such as thermal efficiency, specific fuel consumption, indicative pressure and indicative pressure will vary depending type of fuel used. The model is developed Fuel for diesel engine control purpose when running on biodiesel. Spray behavior of biodiesel is not covered in this work but some useful computational studies about the topic can be found in [14,15], and it will be inserted in further development of the model.

2. Governing Equations

The model used in the present study is a semi-empirical model, based on the work of I. I. Wiebe [1] and the heat release calculation model of Watson [2] and the work of Grondin [3], figure 1 shows a flow chart description of the model, where one can see the input information needed as well as the output data obtained from the model. The next section presents the main governing equations of the model as well as the constant used for our calculations. The model was implemented using an open source calculation code for rapid treatment of the information.

2.1. Ignition Delay Model

The initial Wiebe model was not taking into account the ignition delay period when calculating the combustion process. Wiebe model computes the heat release starting from the injection start angle, whereas it has been shown that ignition occurs after a certain amount of time after injection (ignition delay), due to complex chemistry processes.

In our model we used the model proposed by Hardenberg and Haze [4] which takes into account one of the main properties of the fuel which is believed to influence the delay period as in the cetane number.

, 

where UP is the mean piston speed in m/s; R is the gas constant in J/kmol-K; ε is the compression ratio of the engine; CN is the cetane number of the fuel Pim and Tim are the pressure in bar and temperature in Kelvin at the intake manifold; nc is the polytropic exponent for compression.

2.2. Step by Step Computation

The next step of the model is the fuel engine cycle model; here we determine the pressure inside the cylinder at any angle of rotation of the crankshaft taking into account the start of injection angle the duration of combustion and other parameters. As a result one will be able to determine the different parameters characterizing the efficiency of work of the engine, such as the specific consumption, the effective power and efficiency. The model computes the full process taking place inside the cylinder, with the calculations being made for each stroke of engine cycle.

2.3. Admission Stroke

The pressure of the working medium at the end of the admission stroke is given in Pascal by

,    

where ηυ is the admission coefficient, Pk is the pressure at inlet valves in MPa, Tk the temperature at inlet valves in K, ΔT is the temperature gradient due to the heating of engine elements in MPa, Pr is the residual gases pressure in MPa.

The temperature of the working medium at the end of the admission stroke is given in Kelvin by

,           

where Tk  is the temperature of residual gases in K, ς is the coefficient of residual gases.

The theoretically necessary (stoichiometric) quantity of air for the combustion of 1 kg of fuel is given as, its value is dependent of the chemical composition of the fuel used and is determined by

,         

where, C, H and O are respectively, the ratio of carbon, hydrogen and oxygen in the fuel chemical composition.

The specific volume of the working medium at the end of the admission stroke is given in m3/kg by

,             

where μair is the molecular mass of air.

2.4. Compression Stroke

The parameters of the working medium during the compression stroke are computed using the polytropic process equation.

The pressure at a given time is given in MPa by

where ν is the current value of specific volume defined as

,             

σ is the kinematic function of the motion of the piston

,  

where λ is the ratio of the lengths of the crankshaft and the connecting rod, φ is the current angle of rotation of the crankshaft.

              The specific work of compression is then determined in MJ/Kg by

2.5. Power Stroke2.5.1. Heat Release Model

The admission, compression and ignition delay phase being computed, the next is step of the model is the heat release calculation. Our heat release model computes two phases of the combustion process, the premixed and diffusion phase.

The current fraction of fuel burnt—where φ is the current crankshaft position angle—is computed using a double Wiebe function [2], we then have

,           

with xp and xd representing the fraction of fuel burnt in each phase of the combustion process, β representing the fraction of fuel injected during the premixed phase.

For each phase of the combustion phase (equation 10) we can write

,     

where ai and mi are experimental shaping coefficient of the Wiebe function; φcomb is the start of ignition angle; is the combustion duration for each phase.

The normalized combustion rate (1/deg) is computed by derivation of xi about φ.

2.5.2. Combustion Model

The combustion effectiveness which accounts for heat loss (heat loss due to heat transfer to the walls, hydraulic losses due to the flow of gases) ratio is first defined by

where δ is a heat release factor which takes into account the ration of unburned fuel; ψ—is a ratio of used heat.

The total specific heat of combustion used (instantaneous heat release) is given in MJ/Kg by

,            

where Hu is the net calorific value of the used fuel in MJ/Kg and α is the coefficient of excess air and γ is the ratio of specific heat during the combustion process, according to [16] is value can be taken as constant going from 1.3 to 1.35.

Pressure calculation at any moment of the power stroke is computed using the first law of thermodynamic and can described for the evolution of the pressure/volume indicator diagram from a point 1 to 2 by

,        

where: q1-2 specific heat used to increase the internal energy from point 1 to 2 in the diagram; Cv1-2 is the average specific heat the working medium for constant pressure from point 1 to 2.

Assuming each volume step is small enough and using the trapezoidal method to simplify the integral in formula (14) and expressing Cv1-2 in term of P2 using the Mayer’s formula, we determine the value of the pressure at any given time of the power stroke using the simplified equation

,    

Δx1-2 is the ratio of fuel burnt from point 1 to 2.

Specific work of gases during the combustion stroke is given in MJ/Kg by

.       

Further description of the model can be found in [9], here we presented the main equations for combustion that will have a greater impact on the engine performance calculation.

3. Results and Discussion3.1. Model Validation

The validation of the model consisted in comparing experimental results from previous researches with simulation results using the model. For this purpose, experimental data obtained by Sahoo et al. [17] from a single cylinder diesel at rated speed were compared with the model simulation. To further investigate the validity of the model we proceeded to the simulation of a six cylinder direct injection diesel at different crankshaft rotational speed, results were compared with experimental data obtained by Ahmet et al. [18].

The simulation were performed on a 3 Go of RAM Dual core computer with a time step of 0.1 crank angle degrees, a full simulation took about 6 minutes to complete. The parameters of the model were adjusted to closely match the experimental results. The diffusive combustion duration was estimated about 75 and 60 degrees of rotation of the crankshaft for the first and second experiment respectively using least square fitting technique.

3.1.1. Experimental Setup

Tables 1 and 2 present the engines specifications for each experiment. The default injection timing for the second experiment was determined from the fuel line pressure diagram. The second experiment was performed under varying crankshaft rotational speed—1000, 1250, 1500, 1750 and 2000 rpm.

The calorific value of the diesel fuel was also modified for the second experiment to 42.5 MJ/kg to match experimental input data, remaining properties of the fuel were kept unchanged. To perform comparison we used fuel characteristics that were stated in the work of Sahoo et al. [17], but due to the lack of some relevant information that shall be given as entry parameters to our model we had to add them according to diesel fuel standards. Specifications of the validating fuel can be seen at table 3.

3.1.2. Comparison of Experimental result with Simulation

Figure 2 shows the in cylinder pressure during the combustion phase for experiment number 1. It can be seen that the simulated curve has a similar shape with the experimental curve, the peak pressure, starting and ending pressure values are almost the same. The slight gap between the curves can be due to the fact that the ignition delay model underestimated the experimental ignition delay obtained.

Table 4 shows comparison of simulation results to experimental performances results. It can be seen than the peak pressure is estimated with good accuracy by the model. However the occurrence of the peak pressure is about six degrees earlier in the simulated result, this is an issue that should investigated in further researches. The break power is estimated with an accuracy of 95%,

ReferencesD. Ayhan, “Progress and Recent Trends in Biofuels,” Progress in Energy and Combustion Science, Elsevier, 2007, pp. 1-18.M. Lapuerta, O. Armas and J. R. Fernandez, “Effect of Biodiesel Fuels on Diesel Engine Emissions,” Progress in Energy and Combustion Science, Elsevier, 2008, pp. 198223.A. P. Sathiyagnanam and C. G. Saravanan. “Experimental Studies on the Combustion of a Direct Injection Engine Fueled with SCR,” Proceedings of the World Congress on Engineering, 6-8 July 2011, London.P. A. Lakshminarayanan and Y. V. Aghav, “Modelling Diesel Combustion,” Springer, 2009.Y. Shi, H.-W. Ge and R. D. Reitz, “Computational Optimization of Internal Combustion Engines,” Springer, 2011. http://dx.doi.org/10.1007/978-0-85729-619-1Technologies Gamma, “Gamma Technologies—Engine and Vehicle Simulation,” 2013. http://www.gtisoft.com/P. L. C. Ricardo, “Home—Ricardo,” 2013. http://www.ricardo.com/en-GB/S.A.S Scilab Enterprises, “Home—Scilab,” Scilab Enterprises S.A.S, 2013. http://www.scilab.org/enI. I. Wiebe, “Novelty on Working Process of Internal Combustion Engine (Speed of Combustion and Working Process in Engine) (In Russian),” MachGiz, Sverdlovsk, 1962.G. Olivier, “Modélisation du Moteur à Allumage par Compression dans la Perspective du Controle et du Diagnostic (PhD Thesis),” Université de Rouen, Rouen, 2004.F. Pischinger, E. Scheid and U. Reuter, “Influences of Fuel Quality and Injection Parameters on Self Ignition of Sprays,” Warsaw, 1987.N. F. Razleytsev, “Combustion Simulation and Optimization in Diesels (In Russian),” Vischa Shkola, Kharkov, 1980, p. 169.A. S. Lyshevsky, “Fuel Atomization in Marine Diesels (In Russian),” Leningrad, 1971.X. Wang, K. Li and W. H. Su, “Experimental and Numerical Investigations on Internal Flow Characteristics of Diesel Nozzle under Real Fuel Injection Conditions,” Experimental Thermal and Fluid Science, Elsevier, 2012, pp. 204-211.X. G. Wang, Z. H. Huang, O. A. Kuti, W. Zhang and K. Nishida, “An Experimental Investigation on Spray, Ignition and Combustion Characteristics of Biodiesels,” Proceedings of the Combustion Institute, Elsevier, 2011, pp. 2071-2077.J. Heywood, “Internal Combustion Engine Fundamentals,” McGraw-Hill Series in Mechanical Engineering, 1988, pp. 560-561.P. K. Sahoo and L. M. Das, “Combustion Analysis of Jatropha, Karanja and Polanga Based Biodiesel as Fuel in a Diesel Engine,” Fuel, Elsevier, 2009, pp. 994-999.A. N. Ozsensen and M. Canakci, “Determination of Performance and Combustion Characteristics of a Dieselengine Fueled with Canola and Waste Palm Oil Methyl Esters,” Energy Conversion and Management, Elsevier, 2011, pp. 108-116.N. Watson, D. A. Pilley and M. Marzouk, “A Combustion Correlation for Diesel Engine Simulation,” Society of American Engineers, 1980. http://dx.doi.org/10.4271/800029F. W. Hardenberg and H. O. Hase, “An Empirical Formula for Computing the Pressure Rise Delay of a Fuel from Its Cetane Number and from the Relevant Parameters of Direct Injection Diesel Engines,” Society of Automotive Engineers, Warrendale, 1979.B. Tesfa, R. Mishra, F. Gu and A. D. Ball, “Combustion Characteristics of CI Engine Running with Biodiesel Blends,” Environment and Power Quality European Association for the Development of Renewable Energies, International Conference on Renewable Energies and Power Quality, Las Palmas de Gran Canaria, 2011.