JEMAAJournal of Electromagnetic Analysis and Applications1942-0730Scientific Research Publishing10.4236/jemaa.2013.58050JEMAA-35487ArticlesEngineering Physics&Mathematics Investigation of Ground Frequency Characteristics ohamedNayel1*Electrical Engineering Department, Assiut University, Assiut, Egypt* E-mail:m_a_niel@yahoo.com060820130508322327April 8th, 2013May 15th, 2013 July 1st, 2013© Copyright 2014 by authors and Scientific Research Publishing Inc. 2014This work is licensed under the Creative Commons Attribution International License (CC BY). http://creativecommons.org/licenses/by/4.0/

Four-electrode method is one of the well-known methods in measuring ground resistivity. But, most faults currents and lightning currents have high frequencies components. It is proposed to develop this method to study ground frequency characteristics. A step like current was injected into ground to measure the ground impedance. The ground impedance is assumed to be frequency dependent parallel resistance/capacitance. Two equations were proved to estimate ground resistivity and permittivity from four-electrode method. An analytical model was proposed to model studied cases. The four electrodes are divided to equal spheres and complex image method had been used to satisfy the boundary conditions and penetration depth effects. The calculated results show good agreement with the measured results.

Ground; Transient; Four Electrode Method; Frequency; Impedance1. Introduction

When designing a grounding system for a specific performance objective, it is necessary to accurately measure the ground resistivity of the site where the ground is to be installed. Grounding system design is an engineering process that removes the guesswork and “art” out of grounding. It allows grounding to be done “right, the first time”. The result is a cost savings by avoiding change orders and ground “enhancements” [1].

The ground impedance frequency characteristic plays an important role in understanding and designing grounding systems. To investigate this issue, samples of ground are tested in laboratories [2,3]. The characteristics of these samples will be changed due to ground excavation, temperature and humidity. There are other methods used in prediction of ground parameters and it depends on electromagnetic wave transmitted and reflected from ground or grounding system analysis [4,5].

Grounding resistivity measuring methods depend on injecting a current through the ground via the probe electrodes. The current flowing through the ground (a resistive material) develops a voltage/potential difference. There are different methods [6,7] such as, four electrode method, deep electrode method and two electrode method to measure and obtain ground resistivity. The most accurate method in practice of measuring the average resistivity of large volumes of undisturbed earth is the four-electrode method. The electrode configurations commonly used for ground resistivity measurements are the Wenner and Schlumberger, illustrated in Figures 1(a) and (b), respectively. Approximating the current electrodes by hemispheres, the apparent soil resistivity ρapp can be computed using the following Equations [1]:

Wenner Method:           (1)

Schlumberger Method:     (2)

When the adjacent current and potential electrodes are close together, the measured ground resistivity is indicative of surface ground characteristics. When the electrodes are far apart, the measured ground resistivity is indicative of average deep ground characteristics throughout a much larger area.

This paper studies the frequency dependence of ground impedance by injecting a step like current in outer electrode of four electrodes method. By using successive image method, four electrodes are modeled in ground with permittivity and conductivity parameter of ground. The ground impedance by the proposed method is studied for different ground parameters and different frequencies.

2. Experimental Setup

The ground resistivity and permittivity is obtained from measured voltage and current waveforms due to wave propagation in the ground to study the effect of frequency.

Figure 2(a) illustrates an experimental setup of four electrode method for ground impedance measuring. A step-like current of 20 nsec rise time is injected from a pulse generator (PG) of 500V. The pulse generator injects the current as charge/discharge cable, so, the injected current is not equal to return current. The four electrode method needs to inject current in outer electrode and return the same current from the other side outer electrode. To overcome the unbalance of pulse generator and connection cable a balance transformer. Figure 2(b), is used to convert unbalance current/voltage to balance current/voltage at high frequency. The balance transformer is connected at the end of connected cable to the pulse generator as shown in Figure 2(a). The current is measured by a CT (Peason model 2877, bandwidth from 300 Hz to 200 MHz), and recorded by a digital oscilloscope (Tektronix TDS 3054 m, bandwidth 500 MHz). Transient voltages were measured by a voltage probe (TEKTRONIX P6139A, bandwidth 500 MHz). The field measurements were carried out in Doshisha University yard site.

The current rise time 20 ns is injected for different distances between electrodes. Four electrodes are buried in the ground, as shown in Figure 1(a), all at depth 0.2 m and spaced (in a straight line) at intervals 2 m between the inner electrodes and 4 m between the outer electrodes.

3. Measured Results

A current, as shown in Figure 3, is injected in electrode (C1) and collected from the outer electrodes (C2) and the two voltages of the two inner electrodes (P1 and P2) , as shown in Figure 4, are recorded with the oscilloscope.

The ground impedance is obtained from the measured voltages and currents (C1, C2, P1, P2). The four electrode method at low frequency is used to obtain the grounding resistance by dividing the potential difference

between two inner electrodes by the injected current at the outer electrodes as follows:

Finally, complete content and organizational editing before formatting. Please take note of the following items when proofreading spelling and grammar:

Define abbreviations and acronyms the first time they are used in the text, even after they have been defined in the abstract. Abbreviations such as IEEE, SI, MKS, CGS, sc, dc, and rms do not have to be defined. Do not use abbreviations in the title or heads unless they are unavoidable.

In the same manner the ground impedance at different frequencies ZG(f) is obtained. The current at injected points to ground (C1, C2) is distorted due to the induced voltage between ground and connection wires. The voltage waveforms at any frequency (f) at inner electrodes are reformed to be as a result of current I by multiplying them Vp1 and Vp2 by I/IC1 and I/IC2 as follows:

The ground impedance is assumed to be consists of parallel resistance RG(f) and capacitance CG(f). From the obtained ground impedance ZG(f) the ground resistance and capacitance are obtained. The ground resistivity is obtained for non-equal four electrode method by the following equation:

As the ground permittivity can be obtained.

Figure 5 shows the calculated ground impedance obtained from the measured results by using Equation (4) and calculated impedance by proposed model in next section. It shows good agreement between measured and calculated results and the dependence of grounding impedance on frequency.

4. Numerical Model4.1. Penetration Depth Effect

Assume a wave travels into a conducting medium [8]. Equation (7) is a solution of the wave equation for a plane wave traveling in the x direction in the conducting medium.

where: d = penetration depth m.

It gives the variation of Ey or Jy in both magnitude and phase as a fuction of x. The electric field Ey or current density Jy deceases to 1/e (36.8%) of its initial value, while the wave penetrates to a distance d called penetration depth [8].

where: f = frequency Hz, µ = ground permeability, s = ground conductivity.

Figure 6 shows the decay of the electric field Ey or currrent density Jy as a function of penetration depth, based on the magnitude of Equation (7). Integrating the absolute value of Equation (7) from x = 0 to ∞ results in E0/d or J0/d. Areas under step functional and exponential curve are equal when step function width is equal to the penetration depth [8] as shown in Figure 6.

It is assumed that all of injected current pass in the area of 1/e depth and the ground resistivity below the penetration depth is proposed to be infinity [9]. The successive image method shown in Figure 7 is proposed to consider the penetration depth in homogenous ground. To make sure that all current pass in the area of 1/e depth, a two layer ground is assumed with a top layer of ground resistaivity r, permitivitty e and depth equal to penetration depth d. The bottom layer is assumed with resistivity = ¥, permitivity = 0 and extended to infinity. The reflication coefficinet between the ground and air is assumed. The bottom layer is assumed with resistivity = ¥, permitivity = 0 and extended to infinity and its reflication coefficient with ground is assumed unity.

The analytical method used to calculate the surface potential profile of the four electrodes and grounding resistance/capacitance assumed each electrode driven into

the ground as a sphere. As electrode length is very short, each electrode is considered as equipotential surface. The relationship between the voltage and current can be written as:

where Ij is the current of the jth electrode (j = 1; 2; 3; 4), Vi is the voltage of the jth electrode, Zmn is the mutual impedance element (i.e., mutual impedance between electrode number m and electrode number n), Znn is the self-impedance of the nth sphere.

The elements of the impedance matrix are calculated as equal to:

where rmn is the distance between mth electrode and nth electrode, rmnp1,2,3,4 are the distances between the mth electrode and the image of the nth sphere and equal to:

Figure 8 shows the varying of apparent ground impedance for er = 10 and 50 and (a = 1 m, r = 1000 Ω×m) with frequency. The apparent ground impedace decreases more sharbly as the ground relative permittivity increases. This is due to the decrease of the capacitive part of apparent ground impedance with the increase of apparent relative permittivity.

Figure 9 shows the varying of apparent ground impedance for r = 1000 and 500 Ω×m and (a = 1 m, er = 10) with frequency. The apparent ground impedances decreases as the ground resistivity decreases. This is due to the decrease of the decrease of gound resistance.

ReferencesIEEE Power & Energy Society, “IEEE Draft Guide for Measuring Earth Resistivity, Ground Impedance, and Earth Surface Potentials of a Grounding System,” IEEE Standards 81-1983, 2012.N. M. Nor, A. Haddad and H. Griffiths, “Performance of Earthing Systems of Low Resistivity Soils,” IEEE Transactions on Power Delivery, Vol. 21, No. 4, 2006, pp. 2039-2047. doi:10.1109/TPWRD.2006.874656B. Anggoro, N. I. Sinisuka and P. M. Pakpahan, “Resistivity and Dielectric Constant Characteristic of Soil If are Treated by Water, Salt and Carbon,” 8th International Conference on Properties and Applications of Dielectric Materials, Bali, June 2006, pp. 893-896.S. Visacro and R. Alipio, “Frequency Dependence of Soil Parameters: Experimental Results, Predicting Formula and Influence on the Lightning Response of Grounding Electrodes,” IEEE Transactions on Power Delivery, Vol. 27, No. 2, 2012, pp. 927-935. doi:10.1109/TPWRD.2011.2179070A. G. Pedrosa, M. A. O. Shroeder, M. M. Afonso, R. S. Alípio, S. de Castro Assis, T. A. S. Oliveira and A. R. Braga, “Transient Response of Grounding Electrodes for the Frequency-Dependence of Soil Parameters,” 2010 IEEE/PES Transmission and Distribution Conference and Exposition: Latin America (T&D-LA), Sao Paulo, 8-10 November 2010, pp. 839-845.I. F. Gonos, A. X. Moronis and I. A. Stathopulos, “Variation of Soil Resistivity and Ground Resistance during the Year,” 28th International Conference on Lightning Protection, Kanazawa, 17-21 September 2006, pp. 740-744.IEEE Power & Energy Society, “IEEE Guide for Safety in AC Substation Grounding,” ANSI/IEEE Standard 80-2000, 2000.F. Kraus, “Electromagnetics with Applications,” 5th Edition, McGraw-Hill, New York, 1999.M. Nayel, “Investigation of Wave Propagation Penetration Depth in Multi-Layer Ground,” IEEJ Transactions on Power and Energy, Vol. 132, No. 8, 2012, pp. 1-6. doi:10.1541/ieejpes.132.728