Ddye-sensitized solar cells (DSSCs) are third generation solar cells developed by O’Regan and Gratzell in 1991 [1]. It converts inexpensive photon from solar energy to electrical energy based on sensitization of wide band gap semiconductor dyes and electrolytes [2]. In this process, several subsystems which work in tandem are interlaced with the adsorbed dye on a semiconductor surface that absorbs the visible and near—IR photons and pumps electrons into the conduction band of the semiconductor which is the electron-mediator for “hole” conduction and the counter electrode catalytic material [3]. The performance of the DSSC is highly dependent on the sensitizer dye and wide band gap material such as TiO₂, SnO₂, ZnO and Nb₂O₅ [4]. TiO₂ is highly preferable due to its ability to resist the continuous transfer of electron under illumination (in the ultraviolet range). Several studies have addressed the use of SnO₂ and ZnO [5,6]. In general, the performance of dye absorption on the surface of TiO₂ molecule determines the efficiency of the solar cell [2] and DSSCs efficiencies of up to 10.4% have been reported for devices employing nanocrystalline TiO₂ films [7]. One of the most efficient sensitizers is produced from the heavy transition metal coordination compound, ruthenium polypyridyl complex which is used widely due to its intense charge-transfer (CT) absorption in the visible light spectrum; good absorption, long excited lifetime and highly efficient metal-to-ligand charge transfer (MLCT) [8]. Ruthenium based complexes are however very expensive and hard to prepare, which restricts their large-scale applications in solar cells, stimulating the search for alternatives such as organic dyes [9]. Organic dyes with similar characteristics and even higher absorption coefficients used for DSSCs with efficiencies of up to 9% have been reported [10-12]. Organic dyes with higher absorption coefficients could translate into thinner nanostructured metal oxide films. This is advantageous for charge transport both in the metal oxide and in the permeating phase, allowing for the use of higher viscosity materials such as ionic liquids, solid electrolytes or hole conductors [13]. Organic dyes used in the DSSC do resemble dyes found in plants, fruits and other natural products and several of these have been used in the production of dye-sensitized solar cells [13-15]. Among the advantages of natural dyes is their easy availability, environmentally friendly, ease of fabrication, low process temperature and low cost of sensitization material production.

Naturally most fruits, flowers and leaves show various colours and contain several pigments which are easily extracted and then employed in DSSCs [16]. The leaves of most green plants are rich in chlorophyll and its application as natural dye has been investigated in many related studies [4,17,18]. Anthocyanins are natural compounds that give colour to fruits and plants and are also largely responsible for the purple-red color of autumn leaves and the red colour of flower buds [19]. In this paper, anthocyanin extracts of flame tree flower, chlorophyll extract from pawpaw leaf and their mixture were the natural dyes used as dye-sensitizers for the preparation of DSSCs.

The flame tree (Delonix regia), also known as royal Poinciana or flamboyant, is a member of the bean family (Leguminosae) widely regarded as one of the most beautiful tropical trees in the world [20]. The anthocyanins from the flame tree are composed of cyanidin 3-O-glucoside (Figure 1(a)) and cyanidin 3-O-rutinoside (Figure 1(b)) [21].

Pawpaw (Carica papaya Linnaeus), belongs to the family of Caricaceae. It is not a tree but an herbaceous succulent plants that posses self supporting stems of spongy and soft wood [22] Pawpaw is a large perennial herb with a rapid growth rate and thrives in tropical climate that is dry when cold and wet when warm [20] The leaves emerge directly from the upper part of the stem in a spiral on nearly horizontal petioles 30 - 105 cm long, hollow, succulent, green or more or less dark purple [23]

Figure 2 shows the SEM image of TiO₂ nanoparticles fabricated using screen printing procedure. The TiO₂ nanoparticles had a mean particle size of 20 nm (TiO₂ nanoparticle that is well sintered enhanced the adsorptivity of natural dye molecules).

Absorption spectra provide necessary information on the absorption transition between the dye ground state and excited states and the solar energy range absorbed by the dye. Figures 3 and 4 show the absorption spectra of Flame tree flower and Pawpaw leaf dye extracts respectively as against N719 dye. The absorption range of N719 dye was from 400 - 600 nm with an absorption peak at 475 nm. The flame tree flower dye extract had an absorption in the frequency range 350 - 500 nm with an absorption peak at 415 nm. The chlorophyll dye extract from the pawpaw leaf had an absorption peak at 430 nm characteristic of chlorophyll pigment and an absorption range from 350 - 550 nm. Chlorophyll absorbs most strongly in the blue and red regions of the absorption spectra.

Figure 5 shows the absorption spectrum of the mixed dyes from the flame tree flower and pawpaw leaves with the absorbability range of 350 - 500 nm while the absorption peak was at 430 nm. This indicated that the absorption peaks of the mixed dye and that of pawpaw leaves dye were the same which could be as a result of them having the same colour or composition as different dyes show different absorption wavelengths due to differences in their compositions [24,25]. The weak absorption of the natural dye pigments in the red is a disadvantage, which affects the efficiency of the DSSC. The op-