1. Introduction

ojapps

Open Journal of Applied Sciences

2165-3917 2165-3925

Scientific Research Publishing

10.4236/ojapps.2025.155083

ojapps-142639

Articles

Biomedical Life Sciences, Chemistry Materials Science, Computer Science Communications, Engineering, Physics Mathematics

Decision-Making during Control Pollutant Emissions from Pellet Burning with Tube Gas Heaters

Kostiantyn

Dudkin

¹ Oksana

Yaroshevska

² Vyacheslav

Irodov

² Halyna

Prokofieva

³ Leontina

Solod

³ Valeria

Tkachova

aCollective Research and Production Enterprise “Energocomplex”, Dnipro, Ukraine

aDepartment of Information Technologies, Dnipro Technological University “Step”, Dnipro, Ukraine

aDepartment of Heating, Ventilation, Air Conditioning, Heat and Gas Supply, Prydniprovska State Academy of Civil Engineering and Architecture, Dnipro, Ukraine

09 05 2025

15 05 1196 1213 1, April 2025 16, April 2025 16, May 2025

2014

This work is licensed under the Creative Commons Attribution International License (CC BY). http://creativecommons.org/licenses/by/4.0/

The article is devoted to decision making regarding controlling the operation of tubular gas heaters (TGH) on wood pellets. Experimental results of the study of the operation of TGH on pellets are used for decision making. Experiments have shown the dependence of undesirable gas emissions, carbon oxides and nitrogen oxides in combustion products, on the parameters of the heater operation. The nature of the dependence is contradictory, it is not possible to simultaneously minimise emissions of carbon oxides and nitrogen, it is necessary to look for compromise solutions. The task was set to find such operating modes of pellet heaters that provide acceptable values of gas emissions at different power levels during heater operation. To solve the problem, we used expert judgements in the form of matrices of fuzzy pairwise comparison of separate results of heater operation with each other. The fuzzy decision selection functions were constructed, which extend not only to the set of experimental results, but also to the whole set of possible variation of the TGN operation parameters. For each selection function, their maxima are found, which provide the operation of TGN at different power modes with acceptable gas emissions values. These results can serve for three-stage control of the TGN.

Green Energy Engineering Wood Pellets Tube Gas Heaters Evolutionary Search Stochastic Optimization Binary Choice Relations

1. Introduction

Tube gas heaters (TGH) can be seen as the development of infrared gas tube heaters (IGTH). IGTHs have a long history of development and use. You can specify these articles [1] - [3] and this comprehensive scientific report [3] . These heaters are serially produced by a number of manufacturers in different countries, for example—ROBERTS GORDON [4] . The main components of such heaters are: automatic gas burner, tube emitter, infrared reflector and exhaust or supply fan. Technical solutions appeared, and due to the change in the heat exchange part, the field of application of gas tube heaters expanded, as reflected in [5] . Finally, pellet tube heaters appeared, and the gas burner was replaced by a pellet [6] [7] . The external view of a pellet burner unit with pellet bunker and control unit in an operating heat supply system and view of the experimental setup for testing pellet burner with tubular gas heater are shown in Figure 1 and Figure 2 . Experimental studies have shown that gas emissions from pellet gas burners depend significantly on the operating modes of tubular gas heaters. Figure 3 and Figure 4 show the operation of gas burners on pellets for two modes of operation. It is of interest to find such operating modes of tube heaters that would ensure minimum gas emissions.

In this paper, evolutionary search methods considering fuzzy experimental data and binary choice relations are used to solve the control problem of tube heaters. Evolutionary search methods have been successfully applied to find solutions to various optimisation problems in the presence of one or more criteria, for example, [8] discusses the use of evolutionary search to solve a multi-criteria problem. Evolutionary algorithms play a dominant role in solving problems with multiple conflicting objective functions. They aim at finding multiple Pareto-optimal solutions, thus in [9] a hybrid constrained evolutionary algorithm (HCEA) is proposed which uses two penalty functions simultaneously. Particle swarm optimisation (PSO) algorithms have been successfully used to solve various complex optimisation problems. However, the balance between diversity and convergence is still a problem that requires continuous study, so evolutionary particle swarm optimisation with dynamic search (EEDSPSO) has been proposed [10] . In [11] , a decision-making approach for fuzzy Fermathean soft set based on a score matrix was proposed. A numerical example has been given to demonstrate the validity of the proposed approach. In [12] , the proposed method is used to predict the output value in empirical applications where the observed value is a range or average of several values rather than a real fixed number. Stochastic optimisation plays an important role in the analysis, design and operation of modern systems [13] . A considerable number of papers have been devoted to stochastic optimisation, most notably [14] [15] . Evolutionary fuzzy systems are one of the greatest advances in the field of computational intelligence. They consist of evolutionary algorithms used to design fuzzy systems [16] . Modelling methods for fuzzy systems have received considerable development in the works [17] [18] . The work [19] uses the developed modification of genetic algorithm to optimise the performance of neural network. In [20] , the concept of trigonometric similarity measure (SM) for spherical fuzzy sets (SFS) is used, which has become very important in solving various pattern recognition and medical diagnosis problems. The approach to solve fuzzy nonlinear programming problems was presented in [21] [22] . In [23] proposed a multi-objective nonlinear programming problem to be solved as a linear programming problem. In [24] used evolutionary algorithm for multi-objective optimisation. In [25] , binary choice relations were used for decision making . This direction was further developed, for example, in [26] - [28] . Decision making in complex systems by methods of self-organisation was developed in the works of Ivakhnenko O. G. [29] and his followers. In the works of Yudin D. Б. [30] [31] , as well as in [32] , computational methods of decision-making theory were considered, in which decision search problems are formulated in terms of binary relations, and the problems of nonlinear mathematical programming are transformed into generalised mathematical programming problems. Methods of evolutionary decision search in problems with binary choice relations were first developed in [33] , then developed in [34] [35] . Finally, in [36] [37] a scheme for constructing an evolutionary selection mechanism for decision making in multi-criteria systems with a sample of fuzzy experimental results was proposed. It is of interest to use evolutionary search methods for decision making with several criteria to control the operation of a tubular gas heater on pellets, which determined the content of this work.

Figure 1 Figure 1. External view of a pellet burner unit with pellet bunker and control unit in an operating heat supply system. Figure 2 Figure 2. External view of the experimental setup for testing pellet burner with tubular gas heater. Figure 3 Figure 3. View of operating pellet gas burner at minimum output. Figure 4 Figure 4. View of operating pellet gas burner at maximum output. 2. The Problem of Fuzzy Modeling of Pellet Burner

Mathematical modeling of a pellet burner for tube gas heater is considered. The basis for this mathematical modeling is the results of an experimental study of the operation of the pellet burner. The results of the study of the work of the pellet burner [33] are presented in the form Tables 1-6 . There are 5 dimensional parameters and 3 dimensionless parameters (complexes) that characterize the operating pellet burner. Dimensional parameters are: burner area, S; useful area for primary air passage, S_p; primary air flow, L_p; total air flow, L; burner power, W. Outlet system functions of the heater: ash transfer by the time, Y_A; concentration CO at exhaust gases, Y_CO; concentration NO_x at exhaust gases, Y_NOx. A relationship was established between dimensionless complexes and parameters in the form

$Π_{1} = S_{P} / S; Π_{2} = L_{P} / L; Π_{3} = W / Y_{A} / {(L / S)}^{2}; ϕ (Π_{1}, Π_{2}, Π_{3}) = 0$ , (1)

where

$Π_{3} = d_{1} {(Π_{1})}^{d_{2}} {(Π_{2})}^{d_{3}} {(1 - Π_{1} Π_{1})}^{d_{4}} {(1 - Π_{1} Π_{2})}^{d_{5}}$ (2)

where parameters $d_{1}, \dots, d_{5}$ are obtained from the condition of minimizing the relative error of the model (2) at the points of the training sequence, namely d₁ = 0.0116, d₂ = 1.465, d₃ = −1.029, d₄ = 6.34, d₅ = −0.14.

3. Materials and Methods

We will assume that the system is characterized by a set of parameters $v = {v^{1}, v^{2}, \dots, v^{N_{v}}}, v \in Ω_{v}$ and there are also initial parameters (functions, criteria) $w = {w^{1}, w^{2}, \dots, w^{N_{w}}}, w \in Ω_{w}$ . We will assume that there is the set of experimental results in the form $u = ‖ v_{j}^{i_{v}}, w_{j}^{i_{w}} ‖, i_{v} = 1, \dots, N_{v}; i_{w} = 1, \dots, N_{w}; j = 1, \dots, N_{f}$ , where $N_{f}$ the number of experiments. The total number of experiments $N_{f}$ was divided into three subgroups $u_{1}, u_{2}, u_{3}$ , so that $u_{1}$ is the subgroup of the minimal heater power $W \in (1 - 6) kW$ , $u_{2}$ is the average heater power $W \in (6 - 18) kW$ , and $u_{3}$ is the maximal heater power $W \in (18 - 50) kW$ , so it may be represent in form:

$\begin{array}{l} u_{1} = ‖ v_{j}^{i_{v}}, w_{j}^{i_{v}} ‖, i_{v} = 1, \dots, N_{v}; i_{w} = 1, \dots, N_{w}; j = j_{1}, \dots, N_{f_{1}} \\ u_{2} = ‖ v_{j}^{i_{v}}, w_{j}^{i_{v}} ‖, i_{v} = 1, \dots, N_{v}; i_{w} = 1, \dots, N_{w}; j = j_{2}, \dots, N_{f_{2}} \\ u_{3} = ‖ v_{j}^{i_{v}}, w_{j}^{i_{v}} ‖, i_{v} = 1, \dots, N_{v}; i_{w} = 1, \dots, N_{w}; j = j_{3}, \dots, N_{f_{3}} \end{array}$ (3)

If we give the experimental results an expert assessment using fuzzy comparisons of the results with each other, then we will obtain a fuzzy correspondence matrix of experiments, which can be represented in the form

$\begin{array}{l} Z_{1} = ‖ z_{i j} ‖, i = 1, \dots, N_{f_{1}}; j = 1, \dots, N_{f_{1}} \\ Z_{2} = ‖ z_{i j} ‖, i = 1, \dots, N_{f_{2}}; j = 1, \dots, N_{f_{2}} \\ Z_{3} = ‖ z_{i j} ‖, i = 1, \dots, N_{f_{3}}; j = 1, \dots, N_{f_{3}} \end{array}$ (4)

For expert evaluation the rating scale was used $z_{i j} \in {0; 0.3; 0.4; 0.5; 0.6; 0.8; 1.0}$ , which make sense: {much worse; worse; slightly worse; comparable; slightly better; better; much better}. We also assume that the fuzzy binary relation ${\tilde{R}}_{S 1}$ with the membership function $μ_{R_{S 1}} (z, z)$ is known. We assume that the known selection function $Γ_{1} (z)$ is such that $Γ_{1} (z (x_{1})) \geq Γ_{1} (z (x_{2})) \equiv z (x_{1}) {\tilde{R}}_{S 1} z (x_{2}), \forall x_{1}, x_{2} \in Ω_{1}$ .

And we assume that the known selection function $Γ_{2} (z)$ with fuzzy binary relation ${\tilde{R}}_{S 2}$ with the membership function $μ_{R_{S 2}} (z, z)$ is known, so that $Γ_{2} (z (x_{1})) \geq Γ_{2} (z (x_{2})) \equiv z (x_{1}) {\tilde{R}}_{S 2} z (x_{2}), \forall x_{1}, x_{2} \in Ω_{2}$ .

And we assume that the known selection function $Γ_{3} (z)$ with fuzzy binary relation ${\tilde{R}}_{S 3}$ with the membership function $μ_{{\tilde{R}}_{S 3}} (z, z)$ is known, so that $Γ_{3} (z (x_{1})) \geq Γ_{3} (z (x_{2})) \equiv z (x_{1}) {\tilde{R}}_{S 3} z (x_{2}), \forall x_{1}, x_{2} \in Ω_{3}$ .

It is necessary to find a solution $x \in Ω_{1}$ and for all $y \in Ω_{1}$ so that

$Γ_{1} (x) \geq Γ_{1} (y)$ . (5)

And it is necessary to find a solution $x \in Ω_{2}$ and for all $y \in Ω_{2}$ so that

$Γ_{2} (x) \geq Γ_{2} (y)$ . (6)

And it is necessary to find a solution $x \in Ω_{3}$ and for all $y \in Ω_{3}$ so that

$Γ_{3} (x) \geq Γ_{3} (y)$ . (7)

Algorithm with Mathematical Expectations

In the binary relations (5)-(7) we replace selection function $Γ_{1} (z)$ , $Γ_{2} (z)$ , $Γ_{3} (z)$ the sample mean values, which is calculated in the form

$\begin{array}{l} {\bar{Γ}}_{1} (x, θ) = 1 / n_{i} \sum_{i}^{n_{i}} Γ_{1} (x, θ_{i}), {\bar{Γ}}_{2} (x, θ) = 1 / n_{i} \sum_{i}^{n_{i}} Γ_{2} (x, θ_{i}), \\ {\bar{Γ}}_{3} (x, θ) = 1 / n_{i} \sum_{i}^{n_{i}} Γ_{3} (x, θ_{i}) . \end{array}$ (8)

where $θ_{i}$ -implementation of a random process, $n_{r}$ -total number of realizations of a random process. We replace binary relation (5)-(7) with

$\begin{array}{l} x {\tilde{R}}_{\bar{S} 1} y \equiv {\bar{Γ}}_{1} (x, θ) \geq {\bar{Γ}}_{1} (y, θ), x {\tilde{R}}_{\bar{S} 2} y \equiv {\bar{Γ}}_{2} (x, θ) \geq {\bar{Γ}}_{2} (y, θ), \\ x {\tilde{R}}_{\bar{S} 3} y \equiv {\bar{Γ}}_{3} (x, θ) \geq {\bar{Γ}}_{3} (y, θ) . \end{array}$ (9)

The methods for solving the problems are based on the approach to the evolutionary search for ${\tilde{R}}_{S}$ -optimal solutions. For subset $X$ , $X \subset Ω$ we denote the function of choice in the form

$S (X) = {x \in X | \forall y \in [X \ S (X)], x {\tilde{R}}_{S} y}$ (10)

We shall assume that set $S (X)$ contains the concrete number of elements— $N_{o p}$ .

We shall that for the set Ω it was determined relation ${\tilde{R}}_{G}$ with membership function $μ_{{\tilde{R}}_{G}} (x, y)$ : $Ω \times Ω \to [0, 1]$ . Relation ${\tilde{R}}_{G}$ will be termed generation relation. For subset $X$ , $X \subset Ω$ we denote the function of generation in the form

$G (X) = X \cup G_{H} (X)$ (11)

$G_{H} (X) = {y \in Ω | \exists x \in X, y {\tilde{R}}_{G} x, μ_{{\tilde{R}}_{G}} (x, y) > 0}$ (12)

We shall assume that set $G (X)$ contains the concrete number of elements—N_E.

The algorithm to search ${\tilde{R}}_{S}$ -optimal solution can be represented as

$X_{k} = S (G (X_{k - 1})), k = 1, 2, \dots$ (13)

The iterate algorithm (13) is the general form of evolutionary search.

According to [34] [35] we will consider the decomposition

$X_{k} = \cup_{j = 1}^{N_{B}} X_{j k}, X_{i k} \cap X_{j k} = \emptyset$ (14)

The algorithm (13) takes the form

$X_{j k} = S (G (X_{j k - 1})), k = 1, 2, \dots; j = 1, 2, \dots, N_{B}$ (15)

These iterate algorithms (13), (15) are the general form of evolutionary search.

The evolutionary search algorithm converges to the most preferred solution of choice relation. This position has been theoretically and experimentally proven for clear choice relationships. For a fuzzy choice, this position is based on experimental results. Suppose that the solutions that passed the selection at some step of the iteration for all branches of the evolutionary search have the form ${x_{l j}^{i}}$ , where i is the number of the variable value, for the selected l-th solution $l = 1, \dots, N_{l}$ in the j-th branch of the search $j = 1, \dots, N_{B}$ . Average values for all selected solutions can be calculated as follows:

$x_{0}^{i} = \frac{1}{N_{B} N_{l}} \sum_{j = 1}^{N_{B}} \sum_{l = 1}^{N_{l}} x_{l j}^{i}$ (16)

At the same time, the values of the empirical dispersion will be

$σ_{і}^{2} = \frac{1}{N_{В} N_{l} - 1} \sum_{j = 1}^{N_{В}} \sum_{l = 1}^{N_{l}} {(x_{l j}^{i} - x_{0}^{i})}^{2}$ (17)

The generation of new solutions at the next step of the iteration is performed with a normal distribution for each.

Parameter $x^{i}$ and centers in $x_{l j}^{i}, j = 1, \dots, N_{B}$ , and variance $σ_{i}^{2}$ . That is, the membership function $μ_{R_{G}}$ for the fuzzy generation relation is the density function of the normal distribution:

$μ_{R_{G}} (y^{i}, x^{i}) = \frac{1}{σ_{i} \sqrt{2 π}} \exp [- \frac{1}{2} {(\frac{y^{i} - x^{i}}{σ_{i}})}^{2}]$ (18)

4. Results 4.1. Isolation of Experimental Data for the Minimum Power of a Tubular Heater

The experimental data for the minimum power of a tubular heater was presented in Table 1 .

Table 1 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 1. Experimental data for the minimum power of a tubular heater.

№	S	S_P	L	L_P	W	Y_A	Y_CO	Y_NOx
	m²	m²	m³/h	m³/h	kW	g/min	mg/m³	mg/m³
1	0.0025	0.00021	201	2.7	6.4	3.57	2765	89
2	0.0025	0.00021	168	4.1	9	7	2902	134
3	0.0025	0.00021	215	2.2	4.7	1.6	1429	146
4	0.0025	0.00021	178	2.5	5.3	1.8	812	201
5	0.0025	0.00021	167	2.8	4.5	0.7	2148	160
6	0.0025	0.00021	155	3	6	1.7	722	265
7	0.0025	0.00021	127	2.5	8.2	1.9	1099	134
8	0.0025	0.00021	123	3	9	1	450	188
9	0.0025	0.00021	210	2.75	3.9	1.3	2926	161
10	0.0025	0.00021	175	4.1	9	3.4	6663	56
11	0.0025	0.00021	172	4.3	7.5	5.6	2845	148
12	0.0025	0.00021	152	2.2	5	5	1826	116

All experimental data of Table 1 are divided into two arrays—training and test data, Table 2 and Table 3 .

Table 2 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 2. The experimental data for the minimum power of a tubular heater—training sequence.

№	S	S_P	L	L_P	W	Y_A	Y_CO	Y_NOx
	m²	m²	m³/h	m³/h	kW	g/min	mg/m³	mg/m³
1	0.0025	0.00021	201	2.7	6.4	3.57	2765	89
2	0.0025	0.00021	215	2.2	4.7	1.6	1429	146
3	0.0025	0.00021	178	2.5	5.3	1.8	812	201
4	0.0025	0.00021	123	3	9	1	450	188
5	0.0025	0.00021	210	2.75	3.9	1.3	2926	161
6	0.0025	0.00021	175	4.1	9	3.4	6663	56
7	0.0025	0.00021	172	4.3	7.5	5.6	2845	148

Table 3 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 3. The experimental data for the minimum power of a tubular heater—test sequence.

№	S	S_P	L	L_P	W	Y_A	Y_CO	Y_NOx
	m²	m²	m³/h	m³/h	kW	g/min	mg/m³	mg/m³
1	0.0025	0.00021	168	4.1	9	7	2902	134
2	0.0025	0.00021	167	2.8	4.5	0.7	2148	160
3	0.0025	0.00021	155	3	6	1.7	722	265
4	0.0025	0.00021	127	2.5	8.2	1.9	1099	134
5	0.0025	0.00021	152	2.2	5	5	1826	116

4.2. Isolation of Experimental Data for the Average Power of a Tubular Heater

The experimental data for the average power of a tubular heater is presented in Table 4 .

Table 4 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 4. Experimental data for the average power of a tubular heater.

№	S	S_P	L	L_P	W	Y_A	Y_CO	Y_NOx
	m²	m²	m³/h	m³/h	kW	g/min	mg/m³	mg/m³
1	0.01	0.00643	633.6	46.8	18	0.21	4500	257
2	0.0025	0.00021	165	4.3	18	10	7214	109
3	0.0025	0.00021	151	5.1	18	7	7844	125
4	0.0025	0.00021	201	2.8	11.3	4.9	1311	193
5	0.0025	0.00021	182	3.9	12.8	3.6	779	212
6	0.0025	0.00021	150	3.5	11.2	2.8	617	259
7	0.0025	0.00021	140	4	18	5.4	1144	240
8	0.0025	0.00021	111	3.4	11.3	1.9	246	151
9	0.0025	0.00021	105	3.8	15	3	438	190
10	0.0025	0.00021	97	4.1	15	4.8	1225	238
11	0.0025	0.00021	80	6.5	18	10.8	945	217

All experimental data in Table 4 was divided into two arrays—training and test data, Table 5 and Table 6 .

Table 5 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 5. Experimental data for the average power of a tubular heater—the training sequence.

№	S	S_P	L	L_P	W	Y_A	Y_CO	Y_NOx
	m²	m²	m³/h	m³/h	kW	g/min	mg/m³	mg/m³
1	0.01	0.00643	633.6	46.8	18	0.21	4500	257
2	0.0025	0.00021	151	5.1	18	7	7844	125
3	0.0025	0.00021	201	2.8	11.3	4.9	1311	193
4	0.0025	0.00021	182	3.9	12.8	3.6	779	212
5	0.0025	0.00021	111	3.4	11.3	1.9	246	151
6	0.0025	0.00021	80	6.5	18	10.8	945	217

Table 6 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 6. Experimental data for the average power of a tubular heater—the test sequence.

№	S	S_P	L	L_P	W	Y_A	Y_CO	Y_NOx
	m²	m²	m³/h	m³/h	kW	g/min	mg/m³	mg/m³
1	0.0025	0.00021	165	4.3	18	10	7214	109
2	0.0025	0.00021	150	3.5	11.2	2.8	617	259
3	0.0025	0.00021	140	4	18	5.4	1144	240
4	0.0025	0.00021	105	3.8	15	3	438	190
5	0.0025	0.00021	97	4.1	15	4.8	1225	238

4.3. Isolation of Experimental Data for the Maximum Power of a Tubular Heater

The experimental data for the maximum power of a tubular heater was presented in Table 7 .

Table 7 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 7. Experimental data for the maximum power of a tubular heater.

№	S	S_P	L	L_P	W	Y_A	Y_CO	Y_NOx
	m²	m²	m³/h	m³/h	kW	g/min	mg/m³	mg/m³
1	0.005	0.00286	572.4	25.2	33.5	2.1	510	293
2	0.005	0.00286	543.6	23.4	31.3	2.88	6734	207
3	0.005	0.00286	543.6	21.6	54.7	2.77	43	259
4	0.01	0.00643	651.6	54	32	0.47	694	205
5	0.01	0.00643	684	50.4	35.5	5.5	110	230
6	0.0025	0.00021	196	3	10	5	1019	210
7	0.0025	0.00021	136	4.5	22.5	10.5	853	257
8	0.0025	0.00021	128	7	22.5	11.3	783	261
9	0.0025	0.00021	85	5	22.5	10.3	830	203
10	0.0025	0.00021	168	5.1	18	35	1986	131

All experimental data in Table 7 was divided into two arrays—training and test data, Table 8 and Table 9 .

Table 8 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 8. Experimental data for the maximum power of a tubular heater—the training sequence.

№	S	S_P	L	L_P	W	Y_A	Y_CO	Y_NOx
	m²	m²	m³/h	m³/h	kW	g/min	mg/m³	mg/m³
1	0.005	0.00286	572.4	25.2	33.5	2.1	510	293
2	0.005	0.00286	543.6	23.4	31.3	2.88	6734	207
3	0.005	0.00286	543.6	21.6	54.7	2.77	43	259
4	0.0025	0.00021	196	3	10	5	1019	210
5	0.0025	0.00021	136	4.5	22.5	10.5	853	257
6	0.0025	0.00021	128	7	22.5	11.3	783	261

Table 9 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 9. Experimental data for the maximum power of a tubular heater—the test sequence.

№	S	S_P	L	L_P	W	Y_A	Y_CO	Y_NOx
	m²	m²	m³/h	m³/h	kW	g/min	mg/m³	mg/m³
1	0.01	0.00643	651.6	54	32	0.47	694	205
2	0.01	0.00643	684	50.4	35.5	5.5	110	230
3	0.0025	0.00021	85	5	22.5	10.3	830	203
4	0.0025	0.00021	168	5.1	18	35	1986	131

4.4. Expert Evaluation the Rating Scale

For expert evaluation the rating scale was used $b_{i j} = {0; 0.3; 0.4; 0.5; 0.6; 0.7; 1.0}$ ; which make sense: {much worse; worse; slightly worse; comparable; slightly better; better; much better}. Two sets were identified for expert evaluation: 1) training sequence array, 2) testing sequence array. These heater comparison matrices are presented below

Comparison matrix for minimum power heaters training sequence array

0.5, 0.4, 0.2, 0.1, 0.5, 0.8, 0.5

0.6, 0.5, 0.3, 0.1, 0.7, 0.8, 0.6

0.8, 0.7, 0.5, 0.3, 0.7, 0.8, 0.7

0.9, 0.9, 0.7, 0.5, 0.9, 1.0, 0.9

0.5, 0.3, 0.3, 0.1, 0.5, 0.8, 0.5

0.2, 0.2, 0.2, 0.0, 0.2, 0.5, 0.2

0.5, 0.4, 0.3, 0.1, 0.5, 0.8, 0.5

Comparison matrix for minimum power heaters testing sequence array

0.5, 0.6, 0.3, 0.3, 0.4

0.4, 0.5, 0.3, 0.3, 0.4

0.7, 0.7, 0.5, 0.4, 0.5

0.7, 0.7, 0.6, 0.5, 0.6

0.6, 0.6, 0.5, 0.4, 0.5

Comparison matrix for average power heaters training sequence array

0.5, 0.7, 0.4, 0.3, 0.2, 0.3

0.3, 0.5, 0.3, 0.2, 0.1, 0.2

0.6, 0.7, 0.5, 0.4, 0.2, 0.4

0.7, 0.8, 0.6, 0.5, 0.3, 0.6

0.8, 0.9, 0.8, 0.7, 0.5, 0.7

0.7, 0.8, 0.6, 0.4, 0.3, 0.5

Comparison matrix for average power heaters testing sequence array

0.5, 0.3, 0.4, 0.3, 0.4

0.7, 0.5, 0.6, 0.3, 0.6

0.6, 0.4, 0.5, 0.3, 0.5

0.7, 0.7, 0.7, 0.5, 0.7

0.6, 0.4, 0.5, 0.3, 0.5

Comparison matrix for maximum power heaters training sequence array

0.5, 0.7, 0.2, 0.5, 0.5, 0.5

0.3, 0.5, 0.1, 0.3, 0.3, 0.3

0.8, 0.9, 0.5, 0.8, 0.8, 0.8

0.5, 0.7, 0.2, 0.5, 0.5, 0.5

Comparison matrix for maximum power heaters testing sequence array

0.5, 0.1, 0.5, 0.6

0.9, 0.5, 0.9, 0.9

0.5, 0.1, 0.5, 0.6

0.4, 0.1, 0.4, 0.5

4.5. Results for Choice Functions

There are presented results with choice function in the form (19)-(21).

$Γ (x) = \prod_{i = 1}^{5} (1 + a_{1 i} {(a_{2 i} - r_{i})}^{2})$ (19)

$r_{1} = x_{1}^{1} - x_{2}^{1}; r_{2} = x_{1}^{2} - x_{2}^{2}; r_{3} = x_{1}^{3} - x_{2}^{3}; r_{4} = x_{1}^{4} - x_{2}^{4}; r_{5} = x_{1}^{5} - x_{2}^{5}$ (20)

$Γ (x_{1}) \geq Γ (x_{2}) \equiv x_{1} {\tilde{R}}_{S} x_{2}$ (21)

Parameters $a_{1 i}, a_{2 i}$ were obtained after evolutionary search the choice function for array 1 of experimental data and for array 2 of experimental data. The results of evolutionary search the choice function is presented in Tables 10-12 .

Table 10 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 10. Parameters of the fuzzy choice function for the minimum power heater.

	i	$a_{1 i}$	$a_{2 i}$
$a_{1 i}, a_{2 i}$	1	−0.3071252	0.8014811
$a_{1 i}, a_{2 i}$	2	0.1532593	−0.3323147
$a_{1 i}, a_{2 i}$	3	0.4978446	−0.6202395
$a_{1 i}, a_{2 i}$	4	−0.4215357	−0.01208718
$a_{1 i}, a_{2 i}$	5	0.003904735	0.3095479

Table 11 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 11. Parameters of the fuzzy choice function for the average power heater.

	i	$a_{1 i}$	$a_{2 i}$
$a_{1 i}, a_{2 i}$	1	−0.3627225	0.2329837
$a_{1 i}, a_{2 i}$	2	−0.05706916	−0.3366217
$a_{1 i}, a_{2 i}$	3	0.3229559	−0.273395
$a_{1 i}, a_{2 i}$	4	−0.1807748	−0.1512893
$a_{1 i}, a_{2 i}$	5	−0.0007113587	−0.8040671

Table 12 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 12. Parameters of the fuzzy choice function for the maximum power heater.

	i	$a_{1 i}$	$a_{2 i}$
$a_{1 i}, a_{2 i}$	1	−0.4144383	0.1412199
$a_{1 i}, a_{2 i}$	2	−0.1136156	−0.1227887
$a_{1 i}, a_{2 i}$	3	0.2455468	−0.07456189
$a_{1 i}, a_{2 i}$	4	−0.07079072	−0.08849594
$a_{1 i}, a_{2 i}$	5	0.06467061	−0.443341

The choice function in the form (19)-(21) with specific values of parameters $a_{1 i}, a_{2 i}$ , $i = 1, \dots, 5$ was used to solve the problem of generalized mathematical programming: to find maximum of choice function

$\max Γ (x)$ with restrictions: $0.08 \leq Π_{1} \leq 0.7; 0.01 \leq Π_{2} \leq 0.1; 0.001 \leq Π_{3} \leq 0.8$ .

The results of determining the maxima of the selection functions for the three heater powers are shown below ( Table 13 ).

Table 13 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 13. Values of parameters <math display="inline" xmlns="http://www.w3.org/1998/Math/MathML"> <mrow> <msub> <mi> a </mi> <mrow> <mn> 1 </mn> <mi> i </mi> </mrow> </msub> <mo> , </mo> <msub> <mi> a </mi> <mrow> <mn> 2 </mn> <mi> i </mi> </mrow> </msub> </mrow> </math>, <math display="inline" xmlns="http://www.w3.org/1998/Math/MathML"> <mrow> <mi> i </mi> <mo> = </mo> <mn> 1 </mn> <mo> , </mo> <mo> ⋯ </mo> <mo> , </mo> <mn> 5 </mn> </mrow> </math> as the result of solving mathematical programming problem.

	Dimensionless complex $Π_{1}$	Dimensionless complex $Π_{2}$	Dimensionless complex $Π_{3}$
minimum power heaters	0.4420147	0.03648748	0.02673138
average power heaters	0.4619097	0.04038155	0.02226561
maximum power heaters	0.5120847	0.04504298	0.01542043

For gas emission concentrations there are experimental dependencies [6] in the form (22):

For CO:

$П_{4} = b_{1} \cdot ({(1 - П_{1}^{2})}^{b_{2}} / {(1 - П_{1} \cdot П_{2})}^{b_{3}}) \cdot (b_{4} + {(П_{3} / П_{2})}^{b_{5}})$ (22)

where: b₁ = 0.0256, b₂ = 5.945, b₃ = 63.4, b₄ =1.95, b₅ = 0.48.

For NOx:

$П_{5} = а_{1} + а_{2} \cdot {(П_{1})}^{а_{3}} \cdot {(П_{2})}^{а_{4}} \cdot {(П_{3})}^{а_{5}}$ (23)

where: а₁ = 1.096; а₂ = 31.33; а₃ = 3.2155; а₄ = −01776; а₅ = 0.7470.

Using dimensionless dependencies for harmful gases, the corresponding concentrations of harmful gases at different tube heater powers can be calculated in the form of a Table 14 .

Table 14 <xref ref-type="bibr" rid="scirp.142639-"></xref>Table 14. Concentrations of gas emissions at optimum operation modes of heaters.

minimum power heaters $5 kW < W < 9 kW$	average power heaters $9 kW \leq W < 18 kW$	maximum power heaters $18 kW \leq W < 55 kW$
Optimum concentrations CO
$α_{C O} = 0.00307$	$α_{C O} = 0.003001$	$α_{C O} = 0.002205$
20.3 mg/m³	20.04 mg/m³	17.18 mg/m³
Optimum concentrations NO_X
$α_{N O_{X}} = 1.579$	$α_{N O_{X}} = 1.5809$	$α_{N O_{X}} = 1.604$
242.1 mg/m³	242.15 mg/m³	243.9 mg/m³

As it can be seen from the table of gas emission concentrations, at operation of heaters on all three modes of operation at selection of modes from the table of the most preferable modes the conditions for gas emissions are provided in the form of

$α_{C O} \leq 130 mg / m^{3}$ and $α_{N O_{X}} \leq 250 mg / m^{3}$ (24)

Such conditions correspond, in particular, to the current Ukrainian requirements for natural gas combustion. Therefore, providing such conditions for combustion of wood pellets in tubular gas heaters should be considered quite acceptable.

5. Discussion and Conclusions

Three power modes of wood pellet fired tubular gas heaters (minimum power, medium power and maximum power) were determined based on the results of the experiments. The experiments showed that significant gas emission values were observed in each of the modes and it was not possible to minimise CO and NOx emissions simultaneously. The challenge was to find compromise solutions for all modes of heater operation that would provide the most preferred favourable gas emission values. Using fuzzy expert judgements of heater performance, the experimental modes were compared with each other in the form of a matching matrix. Using evolutionary search, fuzzy choice functions were obtained for the three modes of heater operation. For each fuzzy choice function, maxima were found on the entire set of possible parameters, not only on the set of experiments. The obtained dimensionless criteria at the points of maxima give the most favourable values for decision making in all three modes. At the same time, as shown by the final analysis, these modes ensure the operation of tubular gas heaters on pellets at quite acceptable gas emissions. The obtained results can be used to construct a three-stage control of the heater operation mode. To use the fuzzy selection procedure, which takes into account various aspects of the decisions to be made, it is advisable to construct several fuzzy selection functions and then solve a multi-criteria optimisation problem. For its formulation it is also convenient to use binary choice relations.

The use of matrices for pairwise comparisons of objects is a rather cumbersome procedure, and it should be further improved.

Indeed, the results presented in this article primarily pertain to the specific tubе heater under investigation, as they are based on concrete experimental data. As a scientific contribution, the article proposes a decision-making methodology grounded in experimental results, which are interpreted through fuzzy modeling. The methodology involves constructing a choice function and employing expert assessments to establish preferences under multi-criteria conditions. The maxima of the choice function are then identified to support final decision-making. For other types of tube heaters, this methodology can certainly be applied, provided that all necessary research procedures are followed, to determine their own recommended control parameters.

The reliability of the obtained results is ensured as follows. All experimental data are divided into two sequences (sets): a training set and a validation set. The choice functions and their maxima are determined exclusively based on information from the training set, while the validation set is used to assess the reliability of the findings.

The application of evolutionary search methods for decision-making is based on our prior theoretical and experimental results, where the convergence of the developed evolutionary algorithms to the optimal solution, in terms of the binary preference relation, has been proven with probability one.

References 1

Fred, J.P. (1962) Selection and Application of Overhead Gas-Fired Infrared Heating Devices. ASHRAE Journal, 4, 62-66.

Norman, A. (1989) Application of Radiant Heating Saves Energy. ASHRAE Journal, 31, 17-26.

Morton, J.D., Lawre, L.K., Nemeth, R.J., et al. (1992) Issues in the Design of Infrared Radiant Heating Systems. Technical Report, 165. >https://apps.dtic.mil/sti/tr/pdf/ADA261610.pdf

Herschel, W. (2011) Infrared Handbook. Roberts–Gordon LLC, 93. >https://www.rg-cloud.com/RG/manuals/Infrared_Handbook_RG.pdf

Irodov, V.F., Khatskevych, Y.V. and Chornomorets, H.Y. (2017) Development of Technical Decisions for Heat Supply with Tubular Gas Heaters. Bulletin of Prydniprovs’ka State Academy of Civil Engineering and Architecture, 5, 29-35. >http://visnyk.pgasa.dp.ua/article/view/129204

Irodov, V.F., Barsuk, R.V., Chornomorets, G.Y. and Chernoyvan, A.A. (2021) Experimental Simulation and Multiobjective Optimization of the Work of a Pellet Burner for a Tubular Gas Heater. Journal of Engineering Physics and Thermophysics, 94, 219-225. >https://doi.org/10.1007/s10891-021-02290-0

Irodov, V., Shaptala, M., Dudkin, K., Shaptala, D. and Prokofieva, H. (2021) Development of Evolutionary Search Algorithms with Binary Choice Relations When Making Decisions for Pellet Tubular Heaters. Eastern-European Journal of Enterprise Technologies, 3, 50-59. >https://doi.org/10.15587/1729-4061.2021.235837

Khan, W., Salhi, A., Asif, M., Sulaiman, M., Adeeb, R. and Algarni, A. (2016) Evolutionary Algorithms Based on Decomposition and Indicator Functions: State-of-the-Art Survey. International Journal of Advanced Computer Science and Applications, 7, 583-593. >https://doi.org/10.14569/ijacsa.2016.070274

Mashwani, W.K., Yeniay, O., Shah, H., Tairan, N.M. and Sulaiman, M. (2018) Constrained Optimization with Hybrid Evolutionary Algorithms. Hacettepe Journal of Mathematics and Statistics, 48, 931-950. >https://doi.org/10.15672/hjms.2018.625

Li, W., Jing, J., Chen, Y., Chen, X. and Moshayedi, A.J. (2023) Evolutionary Experience-Driven Particle Swarm Optimization with Dynamic Searching. Complex System Modeling and Simulation, 3, 307-326. >https://doi.org/10.23919/csms.2023.0015

Demir, I. (2024) Multi-Criteria Decision-Making Method with Fermatean Fuzzy Soft Sets and Application of Infectious Diseases. Fuzzy Information and Engineering, 16, 74-88. >https://doi.org/10.26599/fie.2023.9270032

Danesh, M., Danesh, S., Maleki, A. and Razzaghnia, T. (2023) An Adaptive Fuzzy Inference System Model to Analyze Fuzzy Regression with Quadratic Programming and Fuzzy Weights Incorporating Uncertainty in the Observed Data. Fuzzy Information and Engineering, 15, 87-99. >https://doi.org/10.26599/fie.2023.9270008

Spall, J.C. (2012) Stochastic Optimization. In: Gentle, J., Härdle, W. and Mori, Y., Eds., Handbook of Computational Statistics: Concepts and Methods, Springer, 173-201. >https://doi.org/10.1007/978-3-642-21551-3_7

Ermoliev, Y., Zagorodny, A.G., Bogdanov, V.L., Ermolieva, T., Havlik, P., Rovenskaya, E., et al. (2022) Robust Food-Energy-Water-Environmental Security Management: Stochastic Quasigradient Procedure for Linkage of Distributed Optimization Models under Asymmetric Information and Uncertainty. Cybernetics and Systems Analysis, 58, 45-57. >https://doi.org/10.1007/s10559-022-00434-5

Ermolieva, T., Ermoliev, Y., Rovenskaya, E. and Obersteiner, M. (2021) Two-Stage Nonsmooth Stochastic Optimization and Iterative Stochastic Quasigradient Procedures for Robust Estimation, Machine Learning and Decision Making. In: Roberts, F.S. and Sheremet, I., Eds., Resilience in the Digital Age, Springer International Publishing, 45-74.

Zadeh, L. (1996) Fuzzy Sets, Fuzzy Logic and Fuzzy Systems. World Scientific. >http://dx.doi.org/10.1142/2895

Sharaf, I.M. (2023) A Cognitive-Based Similarity Measure for Decision-Making with Spherical Fuzzy Information. Journal of Computational and Cognitive Engineering, 2, 331-342. >https://doi.org/10.47852/bonviewjcce3202479

Zedam, L., Ullah, K., Sajjad, H.M., Hussain, A. and Parveen, A. (2023) Maclaurin Symmetric Mean Aggregation Operators Based on Spherical Fuzzy Information and Application to Decision-Making. Journal of Computational and Cognitive Engineering, 2, 266-277. >https://doi.org/10.47852/bonviewjcce3202551

Chen, Z. (2022) Research on Internet Security Situation Awareness Prediction Technology Based on Improved RBF Neural Network Algorithm. Journal of Computational and Cognitive Engineering, 1, 103-108. >https://doi.org/10.47852/bonviewjcce149145205514

Ünver, M., Olgun, M. and Türkarslan, E. (2022) Cosine and Cotangent Similarity Measures Based on Choquet Integral for Spherical Fuzzy Sets and Applications to Pattern Recognition. Journal of Computational and Cognitive Engineering, 1, 21-31. >https://doi.org/10.47852/bonviewjcce2022010105

Umamaheswari, P. and Ganesan, K. (2017) A Solution Approach to Fuzzy Nonlinear Programming Problems. International Journal of Pure and Applied Mathematics, 113, 291-300. >https://acadpubl.eu/jsi/2017-113-pp/articles/13/32.pdf

Jameel, A.F. and Sadeghi, A. (2012) Solving Nonlinear Programming Problem in Fuzzy Environment. International Journal of Contemporary Mathematical Sciences, 7, 159-170. >https://www.researchgate.net/publication/262007823

Iqbal, S., Yaqoob, N. and Gulistan, M. (2023) Multi-Objective Non-Linear Programming Problems in Linear Diophantine Fuzzy Environment. Axioms, 12, Article 1048. >https://doi.org/10.3390/axioms12111048

Peng, F., Lv, L., Chen, W. and Wang, J. (2023) A Projection-Based Evolutionary Algorithm for Multi-Objective and Many-Objective Optimization. Processes, 11, Article 1564. >https://doi.org/10.3390/pr11051564

Fishburn, P.C. (1976) Representable Choice Functions. Econometrica, 44, Article 1033. >https://doi.org/10.2307/1911543

Aizerman, M.A. (1984) Some New Problems in the General Theory of Choice (One line of Research). Automation and Remote Control, 45, 1103-1135.

Aizerman, M.A. (1988) On Some Extensions of the Option Choice Theory (Findamentals of the Pseudocriterion Theory). Automation and Remote Control, 49, 337-347.

Sholomov, L.A. (1986) Design of Multistep Choice Schemes. Automation and Remote Control, 47, 1414-1424.

Ivakhnenko, A.G. (1970) Heuristic Self-Organization in Problems of Engineering Cybernetics. Automatica, 6, 207-219. >https://doi.org/10.1016/0005-1098(70)90092-0

Yudin, D.B. (1983) Methods of Generalized Convex Programming and Estimation of Their Complexity. Doklady Akademii Nauk, 272, 40-43. >https://www.ams.org/mathscinet-getitem?mr=725061

Yudin, D.B. (1985) Multistep Schemes of Generalized Mathematical Programming and the Choice Function. Doklady Akademii Nauk, 282, 1066-1069. >https://www.ams.org/mathscinet-getitem?mr=796945

Kolbin, V.V. (2014) Generalized Mathematical Programming as a Decision Model. Applied Mathematical Sciences, 8, 3469-3476. >https://doi.org/10.12988/ams.2014.44231

Irodov, V.F. (1995) Self-Organization Methods for Analysis of Nonlinear Systems with Binary Choice Relations. System Analysis Modeling Simulation, 18, 203-206. >https://dl.acm.org/citation.cfm?id=208028#

Irodov, V.F., Barsuk, R.V. and Chornomorets, H.Y. (2020) Multiobjective Optimization at Evolutionary Search with Binary Choice Relations. Cybernetics and Systems Analysis, 56, 449-454. >https://doi.org/10.1007/s10559-020-00260-7

Irodov, V., Dubrovskyi, S., Dudkin, K. and Chirin. D. (2024) Evolutionary Search for Some Generalized Mathematical Programming Problems with Binary Choice Relations. Elsevier. >https://doi.org/10.2139/ssrn.4750911

Irodov, V.F., Shaptala, M.V., Dudkin, K.V., Shaptala, D.E. and Chirin, D.A. (2022) Decision-Making at Evolutionary Search During Limited Number of Fuzzy Experiments with Multiple Criteria. Radio Electronics, Computer Science, Control, 1, 167-175. >https://doi.org/10.15588/1607-3274-2022-1-17

Irodov, V., Dubrovskyi, S., Dudkin, K., Chirin, D. and Aldrich, Y. (2024) Evolutionary Search for Stochastic Optimization with Binary Choice Relations under Fuzzy Modeling. Journal of Computational and Cognitive Engineering, 3, 412-420. >https://doi.org/10.47852/bonviewjcce42022658